Search results

I guess a potentiometer in the loop effect is an easy solution without mod your amp.

I noticed that weirdness, too, just yesterday.

What's your schematic? About the thicker sound (A LOT?) and removing the JFET switching, I see some adjustment of the coupling cap, to keep the same low end. Maybe that's the thing.

You could try shielded wire, for input and output. I can't say if it will solve that problem, but you could try. I heard about oscillation issue with this pedal a lot of time, not this PCB in particular, but maybe PedalPCB, too, and also veroboard and protoboard. You could even try to use a...

I got issue with two of them, when I replace the original THAT4301. In a Muzzle PCB. :(

My friend is better equipped than me: sound-card/interface, amp modeling software... I have just my pc with the input mic. I used to connect my pedal through the old Behringer V-Amp (kind of old red Line 6 POD), to make the amp and cabinet emulator. I don't know if I can make the thing. In case...

Hello, a friend of mine asked to me to try my pedals from his home. (A bit like Thomann). He lives a bit far away from my home and he can't come to me every time. Does someone know a method how he can play his guitar at home with the pedals in my home through our computers? It's ok if I have to...

I just built on stripboard the version without the Oscillation control in an 1590A box. After I put the everything into the box, I got a loud oscillation noise that change pitch turning the Intensity control, but even the volume of the guitar. It was causes by the tip of the input plug, it...

Thanks, Feral Filine. TY-250P Datasheet https://eu.mouser.com/datasheet/2/410/TY_250P-1892894.pdf

If I remember well, the inductance of the part that looks like resistors and capacitors are too small. I know just this kind of transformer have the characteristic that can "emulate" pickup. I include this, too. It can help to go close to the pickups specific. Generically, the inductance is a...

I bought that transformer, but I still didn't built the pickup simulator. I have to say I afraid about the frequency range, too. And, because another kind of project, I'm finding other transformers, just a bit more expensive with wider frequency range, like: 60Hz - 25kHz or 20Hz - 20kHz. Do you...

Thank you Hamish. If I have to build a Rat I'll give a chance to your layout. About the other layout, the one owlexifry used (by TagBoard blog) I always keep my wires short, but like someone else I got that issue. Somebody else not. I don't know why.

Is there a document of this project? I can't get it anywhere, and I would like to take a look inside, please.

When I built the Rat using this layout I got oscillation problem at higher gain setting using the bridge pick of my guitar, during the first test of the board before put it into the box. A lot of people got it. And you?

The schematic I posted above seems do it. A Phase Switch. Though the transistor is a JFET, not a BJT. It has some little implementation, too, but it has the switch.

That "+" is for the red LED, it's just on the right. :)

That Tetsuo pedal sounds huge? Excuse, but what does exactly it is? Edit: It doesn't matter. I visit your youtube page. :)

Maybe you could take a look at the waza craft version schematic.

I tried the Muzzle in the loop effect of my Laney LC50 and with the DIY Tonemender by ROG used like preamp directly in a solid state Crate amp (I cabled the Muzzle between the preamp and the power amp). In both the case the volume preamps are clean and low volume, just to test it in my room. I...

I'm sure enough the problem is not the buffer in front, TU-2 or my DIY buffered splitter (op-amp based). This pedal needs a splitter to use the key input. I heard if it's a buffered splitter is even better. The Muzzle is a replica of the Fortin Zuul, and the Fortin has a pair of buffered...