Search results

Using this. Here's the values it's reading

I don't do that stage until I test the circuit on the Micro Proto Board so the jacks and footswitch are not part of the problem. So this is something within the circuit Coda: The schematic calls for J202s, which I don't have, so I used 201s instead. I got them from Tayda, but tested them on my...

Pic of top

Is there anything immediately outstanding as to why I'm not getting anything when active? The only thing I thought was maybe a pot and switch touching, but I put a piece of electrical tape in to stop them. Sound in bypass, but nothing when engaged. I'll post a pic of the top in the reply as...

You can replace it with the B500k, but you're going to lose some of the sweep. A linear pot (A500) will have a steady consistent change as you turn from 1-10. A logarithmic pot (B500) will have the same start and end point for your gain, but much of the turn, from say 1 to 7 (out of 10) will not...

Thanks. That's what I thought when looking at the schematic, but wanted to confirm since I'm still learning (also why I put it in the general questions rather than trouble shooting because I didn't think it was an issue). Again, this thing sounds amazing and everyone should have it in their lineup.

Hello all, I just finished building the Gent Overdrive pedal and I absolutely love it. The only thing I noticed is with the On/Off/On switch, when the pedal is engaged, in the off position of the SPDT it boosts volume significantly over the 2 fail options. Looking at the schematic, it seems...

The Gain pot is a dual linear pot right (B-pot)? So the sweep shouldn't be as noticeable until later in the turn (unlike a logarithmic pot, or A-pot) which has finer tuning throughout the rotation. Have you looked at the schematic to see what caps and resistors are running into it. Maybe you...

2 things. 1. I got a few of those ribbon cables from Lovemyswitches and none of them ever seemed to work 2. I had issues with the breakout board on my Kliche overdrive. When I wired directly to the PCB from the footswitch it worked perfectly. These may not be your problems, but they were for...

I'd love the seller link please

Would love the 1590bb drill template too. I have the 125B top and end. Absolute game changer

First, the Muffin Fuzz, using the components modeled on the Green Russian. This was my first attempt hand painting a pedal, so it's a bit sloppy, but I like it. I was going for the old Vietnam era military Jeep vibe with the top design Second. The Kliche Overdrive. I'm a hockey fan. More...

I used the diagram posted for the Mini, both would have worked, but I'm a visual learner so I went with the one with the pics of the wires!!! Thank you all again, here's a quick demo. I'm a hockey fan (Washington Capitals fan) so had to make my Ovi-Drive

Rewired the footswitch without the mini-board and it works perfectly. Thank you all for your help. I knew it had to either be the jacks or switch because it worked on the proto-board. This pedal sounds awesome!!

If I want to wire a new 3pdt without the little kliche switch board that comes with the pedal, which lugs to to which hole in the main board?

So, with the pedal plugged in, and testing voltage with direct current, I'm getting 9v on the 1044 (blue, left), 16 on the TL072 in the center (red) and 9 on the TL072 with blue circled in the bottom right. To answer carlinB17, I'm getting continuity in all the legs you mention, and no...

My friends kid plays in a band that does mostly rock and metal (Iron Maiden metal, not Deicide metal). I'm building him a pedal for his kids birthday. Amy recommendations for a PCB? Thanks

Getting sound in bypass, nothing on accrued. I've resoldered the jacks. As you can see from the first post, it worked beautifully on the proto board. So maybe I need to redo the footswitch connection now. I'm at a complete loss

I put electrical tape under the jacks in case that was it, then that cut the sound in bypass too. So it has to be issues with the jacks because I get no sound at all, then sound in bypass, then nothing again. I'll pull the wires and resolder everything again tomorrow morning

I did. There was no solder bridge, but I had never used that ribbon before, so I changed it out. I also changed out the stereo jack for a mono. Now I'm getting sound in bypass, but still nothing active. So confused because it sounded great on the protoboard. Here's an updated image: online...