Search results

I forgive you fig, I think it was me also saying I was going to try that build using a power divider instead of needing the higher voltage regulator, I wasn't disappointed, the sweets bit was meant for a joke 😉

I mess up when calculating how many I need for a build, I never solder until all the resistors are places.. now being shown the error of NOT checking for pin 1 on some IC's... 🤦‍♂️ 🤦‍♂️:ROFLMAO:

he has it, handed to him when I was trying to find a specific voltage regulator.

I'm going to ask the extremely stupidly obvious question, with the joys of getting dual gang pots from some vendors.... do you have the wrong taper pot? it's not on you if THEY sent you a c(antilogrhythmic) taper instead of a b(linear) I seethe markings but is it right in the gutz?

A lot of pedals from here, MBP and Aionfx that are chorus, delay or flanger related have the IC's come from there and near the top of the main forum the owner of Cabintech pops in to let us know when he's gotten a new shipment of something..

I once asked for Fig swag.. guess I forgot to send some cheesecake or jars of something made of strawberries...

may have to find something similar IF I ever feel the need for a contest with the 2 extra jfet tester boards I got from OSHPARK ..

even with a drill press, stuff goes off center, just rounder :ROFLMAO: I'm actually on my 2nd press, same size, other 1 just somehow lived for 25 years being a junk store jobber. I just leave them at slowest or 2nd slowest speeds, the bits are sharp it'll cut and not burn the wood, which...

the project got put on the back burner but the amp had a bit higher draw, min 1 ampere so that regulator would likely burn out quick.

Having done industrial work, powder coating is just weighing out how much powder, counting boxes and running through an oven, and only 2 guys doing it is like 1.5~2days. CNC machining takes programming time, then you have cycle time, then double check the measurements, make adjustments.... then...

oh.. 3d printers WERE cheap not to long ago. I got a decent sized UV for under 200. and the smaller nozzle(FDM is their name) run far less, some under $100 if you get it asa kit that you need to find your own square tubing for a frame. Been eyeballing a Creality Ender series to make the bigger...

actually found it, type in bending jig, several items come up.

I'll check, might want to run it through the search bar on the link I provided or 'grab iron jig' I recall Micro-Mark having this plate with different notches that let you bend to a consistent size time after time

I had somethign similar open recently here ya go! I already printed off the 3rd design, and thinking of making the 1st if the other dies... I noticed a little plastic on the IC legs after pushing it through.

see if I can locate that 1, I just took mine apart to finish painting it... post search edit no, I have it installed, I might try desoldering it because I don't have a replacement to cut, might explain why at some settings I get a 2 chords back effect and nothing at any setting similiar to...

might be shielding on/how the chip was made...I'd have to put both on this ancient bullet scale I have and see the diff in grains, meaning 1 has more material in the outer casing...

I have it's brother the tour bus... keep finding settings that fill so many other 'niche' pedals. is a tight soldering job you've done, better than mine but that is such a LOOOOOW bar :ROFLMAO:

for the layman, spread a bunch of bawlz on a pool/snooker table, and just hit 1 of them really hard in to another bunch. And until the reusable fusion powered(like battletech dropship) vehicle is functional, space mining is a faint dream.

says in the notes if you have an 82k laying around, just use that, most won't notice a difference.

if ya wanna twiddle it, it's a glass, if ya want whoosh in a straight forward build in a smaller box, get a phase II from Rob. Neither is better, just flavor of a damn good phaser that you don't need 3 other projects to identify parts to build!