Search results

Awesome, thank you!

This is less of a troubleshooting question than one I'm asking to prevent needing to troubleshoot later - for the key input on the Muzzle (not the pass through setup, just the single input that you would run from a splitter/tuner etc), the "switched tip" is the contact that gets broken when a...

I can, but I think it's a bit unnecessary lol. It's on an isolated 9V one spot wall wart with nothing else in the signal chain, so I don't think either of those should be the issue. I've built enough pedals and this is simple enough that I don't think it's a build issue, was mostly just curious...

Did either of you end up figuring this out? I built mine, the noise floor is kind of high in the low gain mode, but almost unusable in the high gain mode. There's an extremely loud persistent whine in the high gain mode (almost as loud as the signal level itself when playing), curious if anyone...

The dry signal comes through fine, so I suspect it's clipping one of the op amps after the pt2399 somehow.

I unfortunately don't have the pedal anymore, the dude I sold it to does but he said the only thing that changed it was his neck VS bridge. The amount of distortion he's getting is way more than what comes from a pt2399 though, it was pretty absurd lol he sent me a short video that's too big to...

I just built a friend a Dark Rift Delay. I tested it extensively with both a strat and SG, no issues whatsoever (he tested it at my house with the SG too, so he knows it works properly). He took it home, and if he uses the neck pickup on either his PRS or LTD, the repeats distort quite badly...

So I came home from work and just wired everything up including all of the jacks (the benefit to using the headers for the switch and 9V supply) and it works great. Now I need to see if I have an issue with the 3pdt on my Auditorium...

I'll get the transistor voltages when I get back home from work and post em. Looking at the build doc on my lunch break, the resistors appear to all be the correct values, so I don't think that's the problem

Gonna have to go back and check all the resistors, see if I somehow misplaced one or if values migrated in my drawers, occasionally that happens lol

Yeah this makes sense, the supply voltage is all that changes. I have no idea what to make of this lol

I have signal in bypass, LED power, and voltages on all transistors appear to be correct

I guess the power ground reference never actually changes now that I think about it, the LED runs off negative ground too. Might as well wire up some jacks and see if that's the issue lol

The PedalPCB test rig (Auditorium). That's why I'm curious, since this uses the charge pump to get positive ground, I'm wondering if it won't work with the Auditorium (not sure if the jacks get their ground referenced to the PCB ground when not in bypass or if it always stays at the incoming...

I cannot for the life of me figure out why, but I built a Tonevendor MKII and have no effect signal (using PedalPCB test rig). I have signal in bypass, LED power, and voltages on all transistors appear to be correct. Is there any reason the test rig doesn't work when using charge pumps to switch...

Yeah, that was what I'd seen too. I put in a request for an email when available, I may call them to see what their confidence level is regarding the date though lol

Coming to check to see if anyone knows of a source for these now? I'm in the US but willing to pay international shipping depending on cost. BitBox is out of stock. ABRA says they have them in stock, but I was then told that they don't. Thanks!

This is super clean! I typically do waterslide for the graphics, but this looks nice enough that I might have to go this route. As a side note - what lamp did you use for this? The build doc isn't up yet, it's the only part I'm still missing to complete this lol

The tone control is a little strange on this - it's not a traditional high pass or low pass filter. It might be worth socketing the cap and resistor and playing around. The actual easiest thing, now that I look at it, is probably to swap in a smaller cap for C9. Another option is to put a...