Search results

What about photo evidence!? ;) I'm considering slapping together a diy board, myself. Would love to see what your setup ended up being.

Thanks @ANGRY_SWEDE and @p_wats for starting the convo here. I'd love to hear some other folks weigh in, very interested since I'm about to finish up design plans for my two rainbow machines.

A couple pals have been interested in some pedals, so I've built pairs - sold 'em at cost and with full disclosure that I'm still learning. That's been a fun way to supplement the learning curve - plus my buds have appreciated them! Great as gifts, too, if you're feeling generous and need an...

Update - Despite my best efforts I ended up ordering the wrong toggle switch, and the order switch pcb I received was actually an "oval-style" one (my bad, didn't realize earlier). Still, I managed to make it work! For anyone else possibly running into a similar issue: I squeezed the solder...

holy smokes - nice clean work!

@PedalPCB - the order switch I just received is the "circle style" (like in the top screenshot), instead of the "oval style" (like in the middle photo). Should I aim for the PC-mount toggle switch when ordering parts? Thanks!

@p_wats - super helpful, that makes a lot of sense! Thanks for the quick reply, appreciate it.

@twebb6778 , @chongmagic , @p_wats , @thedwest , @HypnoDirge - Ya'll have "Tone" / "Tracking" on the bottom middle and bottom right knobs of your versions of the Leprechaun, just like the original pedal. PedalPCB's build docs refer to these controls as "Regeneration" and "Dispersion". I doubt...

Wondering if there are any obvious pitfalls that I'm not seeing to building my own War Scythe/Hoof Reaper-type pedal? The three PCBs on the inside would be a Kazoo / Trumpeter and a Squidward at the end. I might put an order switch in there for the Kazoo/Trumpeter, we'll see. Slapdash "artist"...

Any luck on this? I was dreaming of a similar idea - I was thinking it'd have to involve a 4PDT for the order switcher?

47nf worked for my build!

considering a triple crown build, myself - any luck on yours @Danbieranowski ?

I asked the same question a bit ago, here's a link to that thread. Overall, folks did like the following power supplies. I'm likely going to go for the CS7. Strymon Zuma Trutone CS7, CS12 Voodoo Labs - Pedal Power 2 Plus, ISO4, 4x4, ISO 5, Pedal Power MONDO Some folks have also had success...

those are some clean builds!

Photos will help us, try to get some and post them. I know a handful of folks (me included) have built/tinkered/modded this one - so we'll be able to assist with some shots. Couple questions off the top: LED working when boxed? Absolutely nothing when the pedal is engaged? No fuzz or noise? Do...

Looks real clean, as usual, @Barry ! I know it's been asked before... where do you get those slick connections (2-wire power and 4-wire stomp switch)?

Once I got the internally trimpots dialed in - we were all good. I think initially, I had some extreme settings with the trims with the switch in the "down" mode, and the pedal sounded all out of whack. Once I realized I could dial things back, it was fun to intentionally manipulate/bludgeon...

What's been said here has worked for my double build (one for me, one for pal). I had to trial a few different PNP/NPN combos until I settled on something I liked. Small Bear had a smattering of different transistors, so I snagged a handful just to play around with it. Some worked better than...

Would be be OK to blast one square hole in the center of the enclosure, instead of (a) waiting for the pre-drilled enclosures or (b) attempting to make the slits? That way there's more room for error? I figure the faceplate will be stiff and sturdy enough on the top... Might be a fool hardy...

Fingers crossed, we'll see if MTK answers!