Search results

Do you have any 1054s on hand? I don't think the 7662 you have in there will deliver enough current

Here's a vid of Seahorse with the HT -

The HT will definitely distort with higher delay times, but I've never had any issues just dropping them in orherwise

Another one of these wobbly guys for a commission. Rate pot increased to 500kC for a wider range of slower speeds C22 & C23 are 33n (higher speed range than stock) DPDT on-off-on to add 220n caps in parallel with C22/23 (slows down the speed of the LFO considerably). Right position adds the...

Madbean Junk Trunk, Agent 00Funk clone with a few mods

Sorry, was going off the PedalPCB Pitch Witch schematic. But yes, the 1k coming off of lug 2

Decrease the delay pot, and increase R9. 10k / 2.2k should be a good starting point. Adjust each as needed. Another thing I like to do with the PT2399 chorus circuits is replace that chip with an HT8970. They're not as common, but they're pin compatible and have around half the min/max delay...

Basic Ocelot with a cranked MicroAmp jammed in at the output. Slightly increased the caps in the sallen-key filter from 2.2n/220p to 3.3n/330p Only other tweaks are subs for things I had on hand - the germs are 1n5817, and the jets are 2SK117s Always a fan of this circuit, but hated the...

Didn't feel like making another thread, so piggybacking these guys. I put delay cap on a switch, so it goes from the stock 220p to 550p. 2SK30 for Q1

Minimal tweak to this one - C3 increased to 3.3n to lower the cutoff frequency, fatten it up a smidge R20 reduced to 100r to reduce minimum attack time D1&2 are 1N5817 S/H switch is now a stomp Used a 2N5089 for the noise transistor IC2 is LM1458 Demo to illustrate the range and...

I don't see these or the NTE equivalent much anymore, but they're a cool alternative to the 308

For a variable decay time, wire a 1M pot in parallel with C9. You may also want to reduce the value of C9 to something like 4.7u or smaller. If you just want shorter decay overall, just reduce the value of C9 For a better range on the sense pot, I'd lower the value or R5, and probably change...

Nothing too fancy, but I've used it in a few commissions - A momentary polarity toggle Both the toggle and momentary switch are SPDT Here's a shitty vid showing it in action with a stuttering sub octave -

For this one, I used Pegz stamps, and Staz-On opaque solvent ink

Built stock except for the diodes- I used some high vf germaniums. I also had to increase C4 to 4.7n to quell these tinnitus inducing oscillations I couldn't otherwise solve. Pretty fun lil box, and definitely a rad alternative to the Shredmaster that it appears to be based on. Huge range and...

Stevie did the screen printing as well. Its the first I've had him do the print, but it turned out ace

Only tweaks to this are the opto- I used a VTL5C1 for a much wider dynamic range than the LCR0203 called for. I also replaced R17 and 18 with a trimpot to better balance the wet signal, as stock it's quite a bit lower than the dry signal I love this circuit, and this is the third one I've...

Another Low Tide, but I used a 470p for C27 to increase the delay time for some wider pitch shifts, and a little less subtlety overall. There's also a 2SK30 in q1, and it's not a huge difference, but is less gainy than the j201s I'd normally use in this spot It's a PedalPCB board, so you...

Totally spaced on doing a report for this lil guy - Excuse the long demos, but this thing inspires me The input starts with a buffer/ splitter, with one side going to the footswitch, and the other to a direct out for driving envelope detectors. The send goes into a Fuzzdog Spluffer, with...

After all that, my favorite by far is still the more traditional Rat (both silicon and LED)- It's simple and it's range is huge. I really enjoyed building and playing with each of these, but I'll definitely stick with the more standard variants as my go-to. My least favorite of this bunch is...