Search results

Any chance we could get a schematic for the Signal Buffer / Inverter?

18vAC to a collosalus

That makes sense. I'm guessing the eeproms would need to be reprogrammed to add a slight delay? Yep- three bypass modules, three Rats / Triads

I've searched, but haven't found anything. I'm using the Intelligent Relays in my triple Rat set for channel switching. Its silent when bypassing or engaging any of the three, but I get a significant pop when swapping from one channel to the next. All six circuits have their own 47r current...

The 1458 is required for the first two stages to operate properly. Tl072 should work for the filter stages though

There's a Zapper right behind it in the first pic🤘🏻.. gonna whip up a few more demos/ reports tomorrow

Built this one a while back, and just dug it out for kicks, and figured I'd make a quick demo and report Nifty lil dual bandpass filters through a decently capable dirt section. No mods, just funky dirt. Gets surprisingly heavy, and maintains a decent amount of clarity with a Tele tuned to A...

I've not- I don't currently have a way to curve trace

Built mostly stock, my tweaks are - R5 increased to 10k to increase the gain of the input stage a bit Distortion increased to 100kD to compensate for the higher LED threshold and change the taper slightly Clippers replaced with Soviet LEDs (1.9vf) C5 increased to 4.7u to push a smidge more low...

I haven't - not much of a treadle guy, but This is the way I'd go about it, and similar to how the Sweep control is implemented in the Lovetone Meatball. If you're using the Aion Lumitron board, it'd be as easy as replacing the Sweep trim with the treadle controlled pot. In yours, you'd also...

I built mine with an MT3608 buck converter

I bothered him just for the photo op, and now he regrets keeping my chair warm

Only built this one to see if I liked it... And, I kinda don't- it's a bit too meaty and congested for me. It was fun to mess with, but I'm not sure I'd ever really have a use for it Used 2SK30 for the JFET, and 2SC1815s for the BJTs. Only mod - I decreased R18 to 4.7k to gain a bit more output...

Post '94 spec DS-1 on AionFX legacy Comet board, Small Clone on MadBean Touch Stone board. Order switch from PedalPCB Only mod to the DS-1 is the clipping diodes- I opted for infrared LEDs for more output volume, and slightly more dynamic range. The Touch Stone is built according to the doc...

This was a quick commission- guy was tired of the unreliability of his Proco Brat, and wanted something to capture the glory of the box box rat. So, here it be. The Rat portion is built to stock Rat2 specs, but with added soft clippers strapped across lugs 1&3 of the Distortion pot (4x 1N4148...

First off- love the graphics and the LED. This circuit is a ton of fun, and I'm glad to see more build reports 🤘🏻 Second- this one would be easy to replace the fuzz with your dirt of choice (Prunes and Custard could be fun 🤔). Tack a wire onto the the junction of C1/R6- this is your fx send...

Built to vintage spec according to the docs, including the TA7136p preamp chip and 1S2743 clippers. Used IR LEDs and an on/off/on toggle for the other clipping options Being a 90s kid and Nirvana fan, I've always liked the DS-1, but I'm digging this thing hard particularly hard. The no diode...

Just ran into this issue as well, using the TL072. Swapping that out for an NJM2904 solved it. The 072 was kinda cool in that it's texture was closer to the Superfuzz, though

The two don't depend on each other but, together and separately, they effect the overall sensitivity and range of the peak detector. The 1458 has a much wider swing than the TL072 called for in the doc

I don't find the reverse sweep terribly useful in this circuit, but MadBean makes the Batwing which has this mode built in. R20 effects the minimum attack time for the peak detector, with the reverse sweep this will give a much more pronounced ducking effect at the onset of pick attack As for...