Search results

I just attached the anode to the left side of R54, looking at the solder side

I wasn't expecting to like it based on the demos I've seen, but as with pretty much every other 2xtreme4u Boss pedal, it's just gotta be dialed in. I was screwing around with some YouTube drum tracks earlier, and it does pretty admirably at bringing both cut and heaviness while retaining a ton...

Preface- these are the first demos with my recently acquired Simplifier clone, so still trying to match the EQ and response of my 2x12 combo. Neighbors were giving me guff about my rodent summonings 🤷🏻 All three built according to the docs, except I used On/On spdts on the XT-2 XT-2 Xtortion...

Except for rewiring the rate LED, this one's built according to the build doc. Used 4580s because that's what I have on hand. I did experiment with an MN3009, and that was cool for a more flangey chorus, but decided to demo the 3007. The vibrato with the 3009 was kinda meh, and became...

You can see the wires where I have the clock module inserted (its the board in the lower left of the gut shot). I'm fairly certain I used a 10kB pot, but it's been a while. The clock module effects speed, pre-delay, and pitch It definitely works better as an arpeggiator than it does as a...

Fallout themed, no-nonsense Rat? 🤤🤤 Edit- oh, shit! Just saw the ME reference!

R1 is 6.8M, R3 is 2.2M. C5 and 6 both increased to 10n. Transistors are 2SC345 Wanted to really lean into the brassy qualities of the original, and ended up with this bass heavy synthy mess Simple, fun, nasty, classic. Give one a go, if you like ugly sounds

Not entirely sure when I built this, but probably around three years ago. Found it in my cable bag the other day, and decided to label and demo it. Built stock as far as I can tell Pretty fun little box that has pretty wide filter sweep. The dirt portion could probably use a little tweak or...

This one's got a few changes, the biggest being my use of a Tesla TL080 clone for the chip. Comp cap is 33pf. Wanted to try to get some DOD Grunge flavor out of it, and I think I got pretty close LED clippers, t filter across C9, which I increased to 27n. Filter values are 10k resistors, and a...

Split the input so the audio runs through a SHO (Moonn hard boost), retaining as clear a signal as possible. Put pin 8 of the 386 on a toggle switch for gain of 20 or 200. The input of the 386 still comes directly from the guitar. Otherwise, built to the doc If I were to do this again, I'd...

New vid after adjusting the trimpots-

Other than the addition of a footswitchable Filter Matrix mode w/ separate Range pot, feedback expression input, and MT3608 boost converter (set at 17.6v) this one's built according to the doc. Not really a flanger fan, and really haven't cared for the other versions of the Mistress I've built...

Clone - PedalPCB Proletarian Similar-ish - Damnation Audio / MAE Parallel Drive For enclosures, I'd suggest also looking at the Hammond 1590j and 1590P1. They both offer a little more depth @ ~2"

I'm digging the red on that enclosure- what finish option is that?

I definitely like the Resonance mod. Expression input for one or both filters ups it's vocal qualities quite a bit For the sensitivity pot,in addition to a logarithmic pot, place a small value resistor between lug 1 and ground. 2.2k would be a good place to start

If you wanna get extra saucy, you can also throw in some Sweet dual expression action

Built mostly stock, mods are - C4 decreased to 2.7u for shorter decay times. C9 & 10 are 27n to shift the lower filter down slightly. R12 & 19 each have a 2MB pot wired in series. These pots serve as Resonance controls for each of the filters. At zero, resonance is stock. Distortion is now on a...

It's a more neutral circuit- shouldn't be too bright or dark. It's possible you put a higher value cap somewhere in one of the filters Got some pics of your build?

Here's the scheme I use This will also give you a pole for the Gain pot, and an led

Not a huge difference. When going larger, you do need to be mindful of clock noise, though. Could probably get away with 1n