Search results

I built Sabros absolutely brilliant Lighthaus (stripped down version of the Openhaus) Both pedals require 2 - 2n1306 Recently I decided to tackle the full on Openhaus finding it hard to get 2n1306 I decided to borrow the two I have in my Litehaus. 1st try was no go so troubleshooting began...

Anybody use a KOT to boost a high gain pedal? And how about Katzenkonig ,Ionosphere(something close to that) , Sonic Titan (just recently built and what an absolute killer pedal and incredibly loud). I think I'm gonna focus on the next few new builds being older circuits Just for the hell of...

Have you adjusted your trimmers? Until I did that I got the same thing. Also check that your switch has good contacts and continuity.

Does anyone know where I can buy genuine 2n1306's and don't cost $10 each? The place I got mine from like 5 years ago is no longer around. Gonna try for a Toneczar Openhaus. I built Sabro's Lighthaus ( a bit stripped down version of the Openhaus) which I really really really like. Figure the...

For me , trimmers are the only way to set bias it's way too difficult for me to ...1) remember an electrical formula or calculation 2) Even if I could remember one actually putting said formula into action is 100 times harder than number 1 (for me) I know that once you have the trimmer set where...

Cool I got a modded DS-1 and a stock 1 and a late model muff this is a combo I havent tried thank you

yeah I have one of those mini Ibanez screamer too that I've used maybe 2 times I wouldn't doubt the /Nux is some derivative of it but wayyyyyyyy better and so cheap that it wont hurt if you dont like it

If not a tubescreamer fan (Which I'm not a hater nor lover of) try a Nux green OD still really pretty cheap and for me kicks every pedal I've thrown at it up several notches super quiet and clean and nice sweep on the tone only the tight metal pedal refused to comply with it.But It enhances...

the more posts I read the about the rat I just might bust out with one tonight ( a board etched that is) kinda hunting for one now Any body have any experience with beavis 4 knob rat? I'm sure theres probably more mods out there but T4KR has a lot of options or again just build one stock?

Ok a Rat build is going to top of build list? Does it play well with other pedals ? does it stack well?

So so many pedals I've built and one of the most iconic pedals (the Rat) I have not made. Why? I've no idea. But it is now on my list. Doing a bit of searching about the rat I see theres a few mods been made to the rat. Anybody have suggestions as to what rat or derivative of it I should build...

LOVELY pedal Very fun... but one FLOCKIN' annoyance and i'm not sure if its just how the its made to sound cause I'm getting fuzz and I can dial in harmonizing but there's this mother flocking like gated static noise just a couple milliseconds long enough to bug the hell outta me to not fall in...

FOR THE MOSFET DRIVER it calls for 1k trim pots I have 5k is that too much to use to bias the bs170's Im assuming thats what theyre for

update built it socketed the leds sounds like crap probably using 2 clear red leds and one diffused red? when cranking the gain it sounds like its saturating soo much it cant take anymore and sounds nothing like the demos which I thought sound good these sound like fets when over biased tmaxxed...

Thanks to all those who take time to read my question and go further to give a response. We're all still learning to some degree I believe So I just used the 27pf I honestly don't and didn't think it'd have an impact on the circuit. What really caught me off guard was the (IMO) was the very...

Building Unchained. Needing 25pf caps. Have none. Have 22pf and 27pf figured one will be high or low and get close to the 25pf HELL NO. MY BATCH OF 22 AND 27PF measure between .078nf and .092nf = 78-92pf seems real high I pull out 15pf to measure and get 0.076nf. I couldnt tell you which ones...

100% THIS!!! always on never leaves the board enhances any guitar I plug in. I have built 4 of these (2 for me) It's the last one in line before the amp on my board which works perfectly for me

Thanks.I kinda figured that but needed some verification. crucial being the key word

I just finished building this. It passes signal when on. It has a kind of phasing sound and a faint high pitch riding in the back ground. more noticable as the note fades There are a couple of substitutions 1 the .47Uf tantalum subbed with 470nf 2 the lm1458 subbed with a NE5532 And when the...

Can anyone tell me the type of rotary switch to be used this build please thank you