Search results

I can’t tell what way they are on yours but on mine the flat/cathode side of the LED is towards the top/jacks. Do you have the depth turned up? I think the trimmers affect the light some but I don’t recall it being a ton.

This came out really nice. Your builds remind me of one of my favorite board games. https://stonemaiergames.com/games/wingspan/

Hmm I’m in. No particular order. Thermionic deluxe-tons of versatility I use it like the dirty channel into my clean amp. Aion andromeda deluxe-I think the clipping section is interesting and works well. I also like the spectrum control. It’s like a more versatile tube screamer I use it...

This has maybe been a bad start for you with PedalPCB. I think the majority of the comments you have received have to do with a few factors. There have been some bots and salespeople posting on the forum lately. Not a ton but enough to be in people minds. The other factor is that Robert the...

This is what I ended up doing. Works for the time being and was pretty inexpensive. https://www.amazon.com/gp/aw/d/B096LPGJTX?psc=1&ref=ppx_pop_mob_b_asin_title I guess you can stack them if you get more than one.

I have done some and it has gone well so far. I just put a fair amount of flux and make sure my iron tip is clean and has a bit of solder on it. I drag soldered an IC recently and it went better than I expected. I have a few sets of these boards that I have been sitting on until I get a...

I’m thinking of doing some non standard wiring for my IVP preamp. Can someone who has completed one bridge these 2 connections and see if it is worth while as a setting. What it should do is engage both the clean and tube voices. Sort of like a clean blend setting both clean and tube drive...

This thread has me thinking about the IVP build I am working on. I initially thought I would do it without the loops but after looking into them a bit I actually think they are kind of interesting. I’m thinking I might do only the pre voice loop. It effectively breaks the pedal into an EQ and...

Some of the solder joints look either cold or starved. I would reflow them and make sure your soldering iron is hot and make sure the tip is wet with solder. I would also clean the board with a toothbrush and some isopropyl alcohol after you are done it will make it easier to inspect your...

I think the noise might be related to your wiring. When the input and output wires are close together or close to board components they can pick up noise. Try pulling the 2 white wires away from the boards and caps. Sometimes I use copper tape and just tape them to the side of the enclosure...

I would probably do the muroida and if you want to get fancy with it you could add some clipping options on a toggle. My favorites are both LEDs or 1 LED and 1 5817. I haven’t built the Frajaeley but I imagine I would like it I would probably change D1 to a 5817 and I think some people have...

If you have this label maker the wheel labeled 3000-24 prints vertically. I bought mine in a kit with the case for not that much maybe $30-40 with all the wheels.

Well made it through the day without getting hurt again. Got 2 walls sided and installed from there the others should be easy. It has been funny since I have been hurt I have been needing to ask for help from my girlfriend and daughter and they are the normally the ones asking for help for me...

Hey FF, Thank you for checking in. The injury is getting better. I can play the guitar 90% of what I could before. It still hurts if I put weight on it. I’m doing some siding on a shed today and it’s uncomfortable to move the panel and work on hands and knees but I can see the end in site...

This was a straight forward build it worked right off no issues. The C25k was a little hard to source. I ended up ordering a bunch from Ali express, they seem to be ok. So far with the pedal it sounds great but I only played it for 10 or so minutes last night. Kind of reminds me of the...

This schematic works on my Marshall DSL. It lights up when open and the light goes out and channel changes when closed. I’m guessing it will work on yours. Now I have new footswitch on my todo list.

That makes me wonder is it possible it just an inline led with an on off switch. I wonder what would happen if you tried jumping it across with an LED? I didn’t realize there were foot switches that worked like this. I have had the same non light up Marshall for 20 or so years now. I’m going...

Yes setup the blade so it cuts pulling towards you. Then undo the top and to tension it you just press the top of the blade into the cut and pull it tight then tighten the knobs. It takes a bit to get the hang of it but then it’s pretty quick. A coping saw would work fine also and you don’t...

I drilled a hole at each of the 4 corners and then connected them with this guy. If you have a fine tooth blade they cut thin aluminum pretty quick. Just a little clean up with a file at the end. Use cheap file tho as the aluminum can mess them up.

I might have misunderstood I assumed it would run a dc adapter or battery for the LED.