Search results

  1. P

    Foxx tone Machine pedalpcb d9b ok?

    Good point. I better order extra to compare and get a good match Thanks Pb
  2. P

    Foxx tone Machine pedalpcb d9b ok?

    true. They are not expensive. It is worth a shot. Thanks Pb
  3. P

    Foxx tone Machine pedalpcb d9b ok?

    I am looking for germanium diodes for a foxx Tone Machine build. Pedal pcb has d9b https://www.pedalpcb.com/product/a8002/ Are they ok for build? Thanks Pb
  4. P

    Foxx tone master transistor selection

    ok great. Thanks. Pb
  5. P

    Foxx tone master transistor selection

    Typical fuzz circuits use a gainier transistor in q2. I noticed that the schematics i have seen for the foxx tone master use all the same transistors 2n3565 , 2n5088 or 2n5089. Is there any value in using a higher gain trans in q2? Eg 2n5088 q1 2n5089 q2 Thanks Pb
  6. P

    Signal Tracer/Injection Pen

    I have one. My only gripes are the case doesn’t fit well and the probe needs to be longer . Other than that it worked well and is a lot easier than setting up an amp and tone generator. Pb
  7. P

    wire recommendation: 24awg? silicon?

    Any recommendations on wire to use for pedal building? I have tried cloth 22awg, and the plastic/vinyl 22awg. I find cloth a bit of a pain to work with but it looks good. The plastic is a bit rigid. Anyone using 24awg...
  8. P

    Blue Breaker, first 2024 build

    That is an interesting idea. Usually they have a boost + blues breaker in a bigger enclosure like the protein Pb
  9. P

    Blue Breaker, first 2024 build

    I am building one now. I will use the b 100 vol pot and instead of 220k below the diodes i am using a 470k. That was suggested by someone here. It sounded great when i breadboarded it Pb
  10. P

    Blue breaker layout and board silk screen mismatch fir r8/r10

    Hi I think the pcb silk screen is right but i thought i would ask. The layout document and pcb differ for r10 and r8 The 1 m resistor looks like apull down on the output. The trace on the pcb looks like that is the correct r10. Thoughts? Pb
  11. P

    tc1044 ground question

    First time using a charge pump. I am looking into building the sunface: https://docs.pedalpcb.com/project/Sunflower-PedalPCB.pdf The tl1044 takes in +9v and pin 5 puts out -9v. Is the ground still the (-) that comes in or the (-) below the 47u cap that joins -9v to ground? maybe dumb question...
  12. P

    What are your favourite blues breaker mods?

    I tried swapping the 220k for a 470k. It made a noticeable difference Thanks Pb
  13. P

    Thermionic build problem

    I built the thermionic beod clone. Great pedal but noticed the presence pot starts to sound scratchy/spitty once turned half. Just a bad pot and replace it? Thanks Pb
  14. P

    Reverb with fv1 chip does it require programming?

    Thanks. That tells me what i needed to know. Pb
  15. P

    Reverb with fv1 chip does it require programming?

    I am wondering if the reverb pedals with fv1 chips need special programming to be useful. I thought if they had an algorithm preloaded that is all you need unless you want to roll your own. Is that correct? Thanks Pb
  16. P

    Question about pedalpcb reverb

    True. The biggest difference for me is the currency exchange these days :-( Pb
  17. P

    Question about pedalpcb reverb

    I see your point. 53$ usd is 71$cdn. Add shipping (pcb and parts) gets you 90$cdn. Pb
  18. P

    Question about pedalpcb reverb

    The gravitation reverb looks interesting. I listened to the levitation youtube clips and I like it. That would suite my needs. The reverb module is $30 at nextgen, nice to see they have it. I suspect I will be about $90 build. I know reverb builds are more expensive due to the extra chips. Pb
  19. P

    Question about pedalpcb reverb

    Interesting. I didn’t know there were no presets for the fv1. Hmm i have more research to do. Thanks Pb
Back
Top