Search results

Anyone out there have the Tayda drill coordinates for the Mouton Fuzz? I can't recall any other PPCB projects with that arrangement of switches. Thanks!

Was just about to post this topic. I'm guessing they figured leaving ~$5 on the table with each pre-drilled enclosure is costing them too much.

Picked this back up again after a bit of time away. Carefully removed all the sockets... no idea how I didn't lose a pad or two. Soldered in the transistors directly (swapped the PN2222a's for 2N2222a's from GPCB), but still the same low output. Cleaned up the joins and the input/output wiring...

Probe. Didn't touch the pots at all.

Plugged everything in and pressed on the top of each transistor with a pencil, but unforutnately no change. Would it be best to just remove the sockets and solder in Q1-Q5 directly? I hesitate to pull out the sockets for fear of ruining a pad, but I'm a bit stumped here.

Got out the audio probe and when I touch the base of Q1, the volume jumps to what I would expect to be correct functionality. And when I press on the back of the PCB on the solder points for Q2 (circled), the volume jumps as well. So I'm guessing the issue is somewhere in that area. Any chance...

Yep, however from what I understand from the schematic, Q2 is wired like a diode with the emitter not connected to anything so it doesn't matter which way it's turned. Flipped it both ways and nothing is changed. At this point I don't think the transistors are the issue behind the low volume...

The MPSA18's I have are right around that hfe, so those seem to be good. Checked all cap and resistor values and those look correct. Guess it's time to get the audio probe. Thanks again for your help!

Swapped in two PN2222A's for the metal can 2N2222A's and the fuzz is now a bit more gnarly with more oscillation, but still no increase in volume, even at max level. Maybe it's the MPSA18's causing the volume drop? Is there an HFE I should aim for with those? These are from Tayda, fwiw.

Thanks Fuzzonaut! I'll try moving some of the transistors around later this evening. Currently have metal can 2N2222A's in both Q2 and Q4. Did you sub in a PN2222A for Q2? Side note: Is there a difference between 2N2222A vs 2N2222? I only have a bag of the former model. And the 2N2222A's I...

Anyone out there put together a Night Destroyer by Moonn Electronics (https://moonnelectronics.bigcartel.com/product/night-destroyer) Got it as a "bonus" along with an order (Thanks, Nils!), and from the description its a clone of the Devi Ever Destructo Noctavia octave fuzz. Demo makes the...

Well, @KR Sound was right. Fired right up after moving Q3 over one pad. I wish all of these were that simple! But going back to my other question... how to determine the correct voltage at each of the transistor pins. Is it as simple as RTDSS (read the data sheet, stupid)? Or is there a formula...

D'oh! Looks like I put the socket in the wrong spot. Thanks so much! Will pull that out and give it ago.

I'm assuming this is an easy question, but here goes... how do you determine the proper voltage at the transistor pins of a given circuit? Is it a formula or would it be on the datasheet for that component? I've read a few forum posts where the person posing the query is asked to provide voltage...

Ended up getting a few VTL5C1 vactrols along with a recent Amplified Parts order. Swapped one in, but no discernible change in the depth/intensity of the vibrato. Although the indicator status LED was much dimmer... I'm guessing that's down to using a diffused yellow LED for status versus...

Yea, I thought about going the Vactrol route instead of rolling my own. Maybe I'll grab a few on my next order, although $6.50 seems kinda steep. Definitely agree on Nils's boards. Really nice guy and the 5 or 6 of his I've put together have been a lot of fun, as well as a learning experience...

I went with the yellow diffused as well, but am not getting much in the way of depth unless that pot is all the way cw. Has that also been your experience? Saw a post on the effectslayouts board for the Magnavibe on which the Good Vibes is based, and they suggested Ireplacing the 100nf cap with...

Hi there. Reviving an old thread... Were you able to determine the cause of the excessive volume and dissimilarity to the DBA Robot in demos? I just finished this build and am having the same symptoms... Volume goes from nil to full blast at about 7:00 on the A100k pot even with the trimmer all...

Thanks again! I'll have at this once my next parts order arrives... forgot I'm all out of 1/4" jacks... d'oh

Following here for ideas. I had purchased a pre-drilled 1590b for another one-knob project that also included an additional hole on the face for a spdt/dpdt. That idea sort of fizzled, so picked up a TSoDF pcb to build out a doom-y type fuzz. But what to do with that other spot? Any good...