Search results

Finally! Changing IC4 to TL072 I got signal to the output jack. I’m using 2N1304 instead of 1306 cause I got them by mistake. Since I only got to hear the signal for a sec or two with everything cranked up I’m not hearing cranking hi gain. Since 1304’s are less Hfe than 1306 I assume is why I...

Bean , I'm hoping you are still around , and if you could take a look at this supposed verified layout. I ask only cause I only build them and know nothing about laying out and by looking seems exactly like yours except a couple discrepancies because aside from what we both found on your layout...

Really thought I had this. In the uploaded pic the green is where I get signal and the yellow is where I don't. I reflowed the solder in that area with no luck and been trying to check the layout to the schematic but I don't see anything else wrong. Could anybody steer me in some direction to...

So yes exactly what I was thinking you confirmed it. So Q6 needs the Gate and Source swapped and the LND150 need to be flipped opposite what the layout shows and I get signal all the way to IC4 pin 3. Furthest I've gotten on this I'm gonna assume no signal on the out jack is gonna be something...

Bean , do you happen to know if the schematic is correct?

THAT WOULD BE AWESOME!!! Thank you You Mad Bean You

Cool well for anyone remotely interested I made progress looking over the schematic where I lost signal or the signal would not pass through to where I "assume " it will be. I noticed the 2N5457 datasheet shows with tranny laying flat side up pins toward my body the leads are from left to right...

This time I used Madbeans layout. Its the furthest I’ve gotten on this monster. I am now signal tracing it and get signal up to and out the gain pot. I had a couple small bridges to fix and found that R7 is either 150 ohm or a 10M neither is correct should be 100k which I have not fixed yet...

Yes I tested the boost before I put it in. Worked fine and does what it's supposed to do except for the mix pot turning the wet signal off when trying to mix in the wet signal in I wired the boost in taking the organ donor out to the boost in and the boost out to the output jack

It took a while but I got it out of the box and some pics with the boost wired in When the mix is turned for more wet signal I lose all volume Before the boost it worked like it should I saw someone post having a similar if not exact same problem and reflowed the FV-1 chip solving his problem...

Not a “wet pot” but the mix pot mixing in or removing the wet signal. My bad .Basically there is no Organ Donor effect at all now. Gonna try and get it back original (but not before I get some pictures first) unless it is one of my pots that have gone bad and that I can fix . I did’nt get a...

so I decided to try another simple boost the JHS The Bomb which after wiring in (I put the boost on the out of the 3pdt switch instead of where it now is between the out of the organ donor to the in of the boost out of boost to effect out lug on 3pdt dumb mistake) sSo now everything works...

I will be able to do that in an hour or two .Etched it myself so it’s a bit ugly.

Yes thats how I wired it and I used a J113. Whats got confused is 1 - both trimmers (the bias and volume) raise and lower the volume and 2- whether it’s in bypass or turned on the 2 trimmers still adjust the volume of the rest of my pedal chain. That just seems really odd behaviour to me...

So I made a board from the schematic above and after fixing a sstuuppidd mistake (diode in backwards) I now have 8.77 v on the jfet and can only bias it down to around 8.45v I\ve wired it in where the organ donor output goes to booster input and booster output to organ donor output.. Oddly...

Just a shout out to PedalPCB for another fine fun pedal with lots of knew sounds to experiment with The pedal? The Organ Donor. After finding faulty wiring on the 3PDT it fired right up. 2nd time soldering the FV-1 to a board and no problems. I just make sure I file my soldering tip...

Having a massive brain fart happening here. Some reason I can't figure this ultra simple wiring. I've omitted the battery snap and thats the only change. when powered up I get no LED's to light up. I think I know where I messed up by running the D.C. ground to the input jack ring lug kinda like...

temol thank you for the response. Since it's for my pedals and I'd like to squeeze as many 9v jacks as I can into the box I naively assumed about 1 amp would handle alot but my salvaged transformer from a Fender Frontman amp is 1/2 an amp from the (frontmans scheme where I got that from) AND I...

Thank You very much

Thank you for the reply I know Google is my friend but Could you tell me how to get the voltage down to 9 volts , possibly?