Search results

i wasn't sure whether to post this in the What's Really Good thread, or the Share Your Music thread, but I feel like this build report deserves an update for something I never expected to happen with this build.. at the start of this year I started tracking x3 new songs for a band. amidst...

kinda looks like a knockoff too

mayonnaise is a 4 transistor big muff with bells. not an opamp muff at all. but it is a great muff regardless.

nah, haven't felt the need to try anything else since i got onto busboard. probably not a silly idea if you have the shelf / drawer space to store the builds. how good that would be. this is pretty much what i do. if the circuit's interesting enough, it goes on the build list. just have to...

💯 agree. like this: pot pins are actually quite thin (0.5mm) https://www.taydaelectronics.com/datasheets/A-1888.pdf regardless, nowadays i just use trimpots instead.. (unless it's got heaps of pots and tricky to dial in with the linear taper)

BUSBOARD!! 🤟 :cool: 🤟 don't even think about wasting your time with a cheap POS board from tayda or whatever. my first breadboard was a cheapy and i thought it was fine... then i got some good busboards from mouser and starting using those. at first i was like "yeah they're pretty good i...

was it this gated when you breadboarded the circuit? (with the exact same transistors, in the same positions, i presume). a MKI is typically gated, but a MKII really shouldn't be.

this could be a part of the problem. i used to use regular bits. a long time ago. then when i started attempting to drill steel chassis for a few amp projects, i grabbed a step bit, as it was recommended. i've been using the same step bit for about 5 years and it's still good. basically...

assuming CJOD is a mere TS808 clone - IME this source code overdrive appears to generate a little more gain, but definitely had a lot more volume output in my breadboard build. could be wrong, but i'm assuming this is just a fancy input buffer note: there's also this 'additional' gain stage...

yep. phase switch is critical. really limits what you can and can't blend if it doesn't have one.

unless the tube device is leaning heavily into doing non-linear things, like distortion, i wouldn’t expect much benefit in this scenario

theoretical behaviour perhaps? most human ears can't hear graphs or waveforms. breadboarding allows you to hear in real time exactly what the circuit sounds like in the rig of your choice.

what's wrong with LF353? been using it as a TL072 sub for a while now without issue. looking through this datasheet... https://www.ti.com/lit/gpn/LF353 not seeing this thing about 10V min

was thinking about this when looking at the schematic. with such wide a range (438 - 743), could be just about anything. what did you choose in the end?

yep this was my initial thought but the guy is claiming: so assuming all components are the same, there has to be a build error somewhere. and ill say it again. Q3e should not be zero.

that’s what i thought

well ive eyeballed the heck out of this layout a few times now and cannot find anything wrong with it vs. the schematic. Q3e should not be zero. it should have some voltage. like 0.1v or thereabouts. there's a clue. ?perhaps there's a short somewhere causing Q3e to have continuity to ground...

appears to be https://tagboardeffects.blogspot.com/2013/07/mindbender-fuzz-compact-layout.html i have previously followed the mindbender schematic when breadboarding... but that 2K fuzz / attack pot value seems kinda dumb to me, so I just went with a 1K pot. (doubt this will change much, but...

probably. it's just a buffer. i actually used/tried a J201, and a 2N5089 in my breadboard build, and both worked fine.

absolutely have. just as well they're only 8 pin. [16 pin is pure masochism when your solder sucker is a POS] yep. @kirt1974 - use flux. - have a good solder sucker. - expect it to take a long time. if all else fails, and you're able/prepared to sacrifice the ICs, you could just snip them...