Search results

Hole 3 on Side A is for the LED. I have it sized for use with an LED bezel so adjust that hole according to your build plans if necessary.

https://drill.taydakits.com/box-designs/new?public_key=NmJGZ3c2NnlDbVR6dEFiSTYvMG8xQT09Cg==

I'm not sure what's changed but now I get a signal on pin 5 of the IC, but a very faint signal on Pin 7 and all of the components in the stack between those two. I've tried reflowing the solder but no change. EDIT: Now the signals not coming through pin 5 again. Thanks for your help everyone...

I've tried testing again and now I get a clear signal on pin 3 of the IC but nothing on any of the other pins or any of the components in the clipping stack. I do have a 47pF in place of a 51pF since the 47pF measured closer to 51pF than the actual 51pF I had in there before.

Looks like one of the solder pads on C1 is gone. Not sure if it happened just now or earlier. I replaced C1 and I am back to getting a very faint signal when I max out all the knobs.

I do not, also the LED is no longer working.

Yeah the PCB lists 25v for all of them which is what I used. I have 50v versions of them as well if that would make a difference.

Ok, I've built an audio probe, but I'm not sure how to use it. I've got the jack on the probe going to an amp and I'm running an audio signal trough the circuit from my phone. I hear the music when I probe the jack, the input on the switch pcb, the in on the main pcb, and the lead of R1 (but not...

Yeah, the LED has always turned on.

Unfortunately, that's not it. I cleaned it up just to be sure but I still get no signal. I will try to wire one of those up. Is there a way to do it with the continuity setting on my multimeter? I tried testing along the signal path and I get a tone from the jack to the switch on up to the...

I have black for + and red for - in this one. Wire color for me is more or less random. Power doesn't seem to be the issue. The LED lights and the pedal seemed to be working for at least a few minutes before it stopped.

Not sure if this is useful but I tried measuring voltage across components to see if/where there was a break in the current but I get a pretty consistent reading across every component I test. Including from out to ground. Is there a good way to work through the circuit path to see if I can...

I've been running into issues with putting together an Oxide pedal. After assembling it, bypass sounded fine but when switched on the pedal was very quiet. I started checking component values with a DMM and found a number that were out of tolerance so I replaced those and the circuit seemed to...

Hole 2 is the LED hole. It is at 6.8mm for using with a chrome bezel so adjust that one if you don't plan on using one.

It looks like this is already on the product page, but I was also able to use this for the Pedal PCB Maleficent Mids.

https://drill.taydakits.com/box-designs/new?public_key=WjVzT1pDT0hGR2pCa05jelpLc1l2dz09Cg==

https://drill.taydakits.com/box-designs/new?public_key=ME9LZEtOQVJMaEY5cHpsWHRqemptdz09Cg==

https://drill.taydakits.com/box-designs/new?public_key=OXhWY2t1NWg1azVHYVB5a3BJMUMrZz09Cg==

Ah dang! That would have been much easier :LOL:

This started with an idea to build a kind of two-stage Klon clone with a built in boost in front of it so that I could use the Klon side as a clean boost and then push it into the heavier clipping with the boost. After trying a bunch of different pedals in front of the Kliche mini I found I...