Stuff

jeffwhitfield said:
Let's see....nope....got it....nope....got it. Strangely enough, the Byzantium and VIIB are the only two that I just don't feel like taking on. Maybe one day...but for now, I kinda have what I need. Already got decent vibrato and flangers. I mean, what good is one more of each? (famous last words)
Click to expand...
What 's the verdict on the Joyo Flanger, I like mine!!!
 
fig said:
Hey, this Pharmacist pcb has some SOT-23 pads for 5457s so I get to use the EZ-Bake again. Those will go on first. I've got to flow a Raincoat module along with it. You know what that means.......more crappy phone pics! yay!

By the way, if you or anyone you know or bump into on the subway ever want to see something built, attempted, explained, etc., just let me know and I'll do my best to A) remember to do it, and B)....well I've forgotten what B was, but I'm sure it's just legalities and disclaimers in the finest of prints.
Click to expand...
I was going to go all out on the Parmacist if I build it?
It was going into 120mm x 120mm Enclosure:
Pharmacist Mockup Pedal 2.jpg
 
jeffwhitfield said:
You know…I never did get one. Should probably get one for posterity’s sake.
Click to expand...
Here's a gut shot:
Joyo use crap hookup wire, nearly every time you open them up a wire breaks off !!!
imgext.php
 
Update on The Pharmacist!

Nothing ground-breaking, but I did select and bake the 5457s on this morning. Naturally, I took some crappy phone pics, as I know how much you enjoy those! :)

One thing (of many I am certain) I failed to point out in my last EZ-Bake oven demonstration, was using the silkscreen for proper alignment. Our tallest saw fit to mark the FETs with a groovy little box, because well, take a look. You can't see the pads due to the paste! Granted, I went a wee heavy with it, but not too shabby.

I13CbdK.jpg

4UNYJ5P.jpg

Liwf8p0.jpg
 
I'm not planning to use these, but when realized the only 5m1Ω resistors I have are SMD :oops: I thought, sure I can do that!

So I made some through-hole 5m1Ω out of them and some .125w through-hole resistor leads.

I used some heat tape to hold the pieces in place. the lead is one piece at this time

WoyhPsT.jpg


After baking...I can see that the rear of the oven is a bit warmer.

2lPOfXu.jpg


Now I just have to snip the bit in the center....careful goofy!

Nc2ycnd.jpg


Hot dog!

dGPIiYj.jpg
 
fig said:
I'm not planning to use these, but when realized the only 5m1Ω resistors I have are SMD :oops: I thought, sure I can do that!

So I made some through-hole 5m1Ω out of them and some .125w through-hole resistor leads.

I used some heat tape to hold the pieces in place. the lead is one piece at this time

WoyhPsT.jpg


After baking...I can see that the rear of the oven is a bit warmer.

2lPOfXu.jpg


Now I just have to snip the bit in the center....careful goofy!

Nc2ycnd.jpg


Hot dog!

dGPIiYj.jpg
Click to expand...

Impressive.
 
After having a song written about me AND winning a pedal, I mowed some grass and made a bit of progress on The Pharmacist!

I ordered some 5m1Ω and I didn't have an 820pF in a suitable package so I have that inbound as well. Incidentally, those ECs are what I'll also be using in the upcoming ElectroVibe Mini build. They are 6.3mm in height and are rated ≥16VDC so (y)

HJJOKiL.jpg
 
Small update on the Parentheses; remember my triple-footswitch guesstimate wiring? No? It's a page or two back, but probably not worth looking....anyway the point is, when the Tayda pre-drilled enclosure arrived for it today...it FELL in...no adjusting or putzing...no kiddin! Even an idiot gets lucky, now and then.

I'm getting worried now. 😟
 
You must log in or register to reply here.
Back
Top