Recent content by temporalhaze

Last night I completed my final build of the year, a Low Tide Modulator! I love these things. In the several I've built I've never outright had an issue from beginning to end. I did however learn the hard way with my first build that the dual gang pot needs to be insulated from contacting the...

Thank you for the pointers! I got the original W20K from SBP and I'll probably go back to them. They're also a 40 minute drive from me, so I'll support the locals where I can 🤘

Last weekend I completed 3 Revel Overdrives and I finally got to testing them and verifying they 100% function yesterday after work! These things are pretty gnarly, and thanks to the help of a few folks over on my mids mod post I was able to implement a mid scoop/boost control on each of these...

Over the weekend I completely my third ever 2-in-1 build - a Hydra Delay feeding into a Spatialist Reverb. The build itself wasn't too bad for either, but the Spatialist side of this led to an interesting troubleshooting session. I had identical symptoms as this thread follows but it wound up...

Sick! Good thinking on lug 2 connecting to R12.2, I hadn't considered that. I actually plan on putting my mid pot square in the middle of the four stock pots just like the original LCFR2 is, and shifting the LED down towards the foot switch.

Ah yes that's right. Did you wind up wiring Lug 2 to the cap also?

I'm stoked to hear that it works! Per Robert's note that it's mainly modeled after an Xotic BB, I decided to go with the W20K pot. The taper on W pots is super interesting too, I'm excited to get one up and running this weekend! I'll definitely either follow up here or make a Build Report post...

I appreciate the quick insight and pointers! This is a huge help to possibly make these builds really awesome. Using the Revel's schematic and the XB-MB schematic for reference here...if I am staring/comparing this correctly, could I add the XBMB's W20K pot in between the junction at R10, C6...

@Robert - tagging you for your two cents if you have any thoughts. I see you're tagged as Staff/Reverse Engineering also. Low priority/whenever you have time. I'm only pushing for movement as I'm looking to make another wave of component purchasing soon. If I could include the needed parts for...

Checking in to post the latest build for my personal collection. I love the sound of this thing and the flexibility in which you can control the LFOs in sync or completely out of sync for maximum weirdness. The build itself wasn't necessarily tough at all, just super dense. The amount of...

Hey all, I recently purchased two Revel PCBs and have been awaiting the build docs as I'm sure others have. While watching some demos, both the v1 [which this PCB seems to be based off] and the v2 seem pretty similar, save for v2 having a boost/cut knob for the Mids, and switchable 9v/18v...

Uhhhhhhhh so I might be an idiot. I think by testing with all pots maxed out, the Slew was also maxed out, basically eliminating any of the jitter and erratic pitch bending of the signal. Now that I hear the erratic bending I was able to adjust the BBD trimmer to taste! Thank you all for your...

IC2 Pin 5: 0%: 3.89-4.05 ~33%: 1.87-2.5 ~66%: 1.17-2.37 100%: 0.44-2.21 IC5 Pins 1 / 7: 0%: 0.23 / 0.13 ~33%: 0.89 / 0.26 ~66%: 0.13 / 0.09 100%: 0.43 / 0.64 IC5 Pins 2/3/4: 0%: 1.22 / 1.34 / 1.37 ~33%: 2.55 / 2.62 / 2.62 ~66%: 2.88 / 2.89 / 2.9 100%: 2.6 / 2.6 / 2.59 Hopefully this helps! I...

I should clarify, I was testing with all pots at 100% except for the Gate, which I tested at varying levels and can hear, and I'm still not hearing the chorusing effect as originally reported. My 3207s just delivered today and no luck, still no Chorus effect on this thing. I'm proceeding with...

Hey hey, so a later weekend update to address a lot of the points on here in-depth now that I'm back home. Preface to rest of my findings: I adjusted the internal switch pad to Off and the Boost to On lower your suggestion, and tested the pedal maxed out at all settings, 100% Wet Blend at all...