Search results

I haven't tried it with too many things, but I was able to get some good tones with a Son of Ben and Mach 1. I like a Kliche set as a boost and stacked with almost anything.

Because I’m still a circuit noob…what does the cap change do? Less treble to ground? Maybe I should socket this one and try both. Out of curiosity, what kind of music do you play? Smooth and gentle is a positive for me as I normally play roots music and use ODs more as slightly dirty boosts...

It is a cut on the Timmy, presumably the Jan Ray as well (but, sounds like, not as well executed). Unless I’m missing your point…

Can confirm! Works great on adult size clothes, however.

Hi all. I made a template for the new Chop Shop with tone switch since I couldn't find one. I have not built this. I have not ordered this. I'm pretty sure it's correct, but I am prone to some silly errors. Please check my work and buyer beware until I confirm with an order. Note I use 5mm LED...

Thanks

Good grief - thank you so much for the corrections. I had misread the discussion on freestompboxes re: the voltage divider. Any thoughts on the volume control? I'm thinking of just leaving it at the Termina values since I think it gets to basically the same place. OTOH, if I used the Jan Ray...

I've had a few real Timmys. I'm doing this version just to see if I actually notice any differences...plus it amuses me to do a clone of a (mostly) clone of a great pedal. Thanks for your thoughts. I'll check out the TSV-808.

I'm wondering if anyone has used the Termina PCB to create a Jan Ray clone. I'm starting with that PCB rather than the Tommy as a quick look (to me) suggests it's easier to change the values to match the Jan Ray schematic. I've compared component to component and it seems pretty...

You did. Totally missed it. Lots of “notes to self” on the journey so far 😀.

Well....don't assume I'm a he and can see very well ;) (I am and I can't thanks to a couple of retina operations....probably shouldn't be soldering small pads with hot irons...haha). But, I was thinking about your suggestion too. I think I should invest in one. I did find the bridge....late in...

Ugggh…careless, thine name is me. Solder bridge on IC2 that I missed first time through. All is fine now. 🤦‍♂️ Agree on the solder joints. This was my first project from PCB. I’m getting better, but still not there.

I’ll add larger ones And bend the pots. I swapped a new 10K for R17 and my desoldering methods needs refining. I figured it might be the problem since the voltages go from 9.08 to 0 across R17 (still do after swapping). Anyway, the leads are connected to the pads…poorly, but connected. The side...

Yes....funny was just about to post. Voltages: IC1 1 - 9.08 2 - 7.18 3 - 3.45 4 - 0 5 - 0 6 - 1.06 7 - 2.51 8 - 2.62 IC2 1 - 9.08 2 - 8.56 3 - 8.54 4 - 0 5 - 0 6 - 0 7 - 8.56 8 - 8.56 Q1 D - 9.08 S - 1.26 G - 0 Pics (weird looking components were mistakes or tried replacing to resolve issues):

C13 replaced. Still get continuity across the leads :unsure:. My voltage is not dividing correctly (Vb not 4.54V), so I'll go back to R17 and R18 to see if I can get them straightened out. Pin 1 and 4 on both ICs read correctly (9.08V and 0V). Pin 2 and 3 on IC1A operate correctly (pin 3 V 1/2...

Double checked. Still continuity on C13. I’ll replace it and report back.

I did. I get Clean Volume side to work, nothing else. I need to replace C13 first and then see. I get continuity between the leads of C13.