Search results

Not sure if this is useful but I tried measuring voltage across components to see if/where there was a break in the current but I get a pretty consistent reading across every component I test. Including from out to ground. Is there a good way to work through the circuit path to see if I can...

I've been running into issues with putting together an Oxide pedal. After assembling it, bypass sounded fine but when switched on the pedal was very quiet. I started checking component values with a DMM and found a number that were out of tolerance so I replaced those and the circuit seemed to...

Hole 2 is the LED hole. It is at 6.8mm for using with a chrome bezel so adjust that one if you don't plan on using one.

It looks like this is already on the product page, but I was also able to use this for the Pedal PCB Maleficent Mids.

https://drill.taydakits.com/box-designs/new?public_key=WjVzT1pDT0hGR2pCa05jelpLc1l2dz09Cg==

https://drill.taydakits.com/box-designs/new?public_key=ME9LZEtOQVJMaEY5cHpsWHRqemptdz09Cg==

https://drill.taydakits.com/box-designs/new?public_key=OXhWY2t1NWg1azVHYVB5a3BJMUMrZz09Cg==

Ah dang! That would have been much easier :LOL:

This started with an idea to build a kind of two-stage Klon clone with a built in boost in front of it so that I could use the Klon side as a clean boost and then push it into the heavier clipping with the boost. After trying a bunch of different pedals in front of the Kliche mini I found I...

Thank you, I did not know about the wiki.

I want to try putting two of the Arche Boosts into one larger enclosure. It should fit physically, but I wanted to ask about how to wire it. I made an MS Paint showing my best guess: + power jack goes to both + on the PCBs - power jack goes to both - on the PCBs Right sleeve (on diagram) goes...

Thank you!

Solution: Capacitor C101 on the 220504 rev should be a 100nF capacitor. I am populating the new 220504 rev of the Informant Overdrive but have an issue with the value of the capacitor at C101. The printing on the pcb looks like it says 100r or a slightly misprinted 100n. The build guide, which...

That makes sense. I was thinking of it like a dying 9V battery lowering the headroom on a pedal but if the 9V measurement is from the drain to ground then what you are saying makes more sense.

This is my third PedalPCB build and the first where I didn't have to come to the forums for help. I just plugged it in and it worked! I love the sound of it, it is definitely going to replace the Son of Ben on my pedalboard as my low wattage amp-in-a-box pedal. I think I may swap the knobs for...

Problem: While trying to bias trim pot 1 on a Son of Ben PCB, the desired resistance was not within the trim pot range even with the trim pot at either extreme. Solution: The jumper between the drain of Q1 and the cathode of D100 was not properly attached. I removed the pcb from the case and...

Thank you both! That is very helpful. I will update the OP and mark this thread as Solved.

I tested the continuity with a multimeter. I got a beep between lugs 2A and 2B and between 3B and the remaining (left) solder pad. Does this help narrow down which holes to bridge?

Thank you! I thought the solder bridge must be mimicking the dual gang in this way. I don't know which of the two options it is but this narrows down the potential solutions. Good spot on the melted capacitor, I will definitely replace it before trying to do anything with the pots.

Here's the spot on the schematic showing the Bass potentiometer that I think the solder bridge effects. I don't see anything on here indicating where that solder bridge is located in the circuit but I am a novice at this. I was able to find some dual gang B1M pots so if I am unable to fix it for...