Search results

I've ordered a Double Muff with my last PCB order, and was thinking of breadboarding the muffin fuzz variants before committing. I was hoping to get another set of eyes over a few parts lists to add to the existing options, I've made some educated guesses with some of them but am open to...

Yeh they were napping the day away and I was just randomly looking out my window and noticed them Outer eastern Melb

Two Tone Fuzz Q1 MP42B 49hfe, 63uA Q2 MP20A 50hfe, 63uA Q3 MP20A 80hfe, 184uA 20K trimmer on R7 here too. I like bias & impedance both up full with my Tele, with a flick of the switch get the Fuzz Face and Tone Bender MkII sounds really nicely, as such Twin Face and Tone Vendor both for sale.

Tone Vendor Mk II Q1 MP42B 46hfe, 166uA Q2 MP20A 55hfe, 170ua Q3 GT402E 115hfe, 101ua 20K Trimmer for R7 bias, 8v on Q3 collector.

Taking these photos through binoculars and my phone is every bit as difficult as it sounds

Yeh that's exactly what I did.

I used the basic dpdt relay for my kliche, works a treat for soft switch. https://www.pedalpcb.com/product/pcb518/

I asked Robert and he said 2 weeks, three weeks ago 🤷‍♀️

I just finished breadboarding a tone vendor mkii with trimmers, then tested it with resistors of the same value successfully. I've just assembled the components onto a PCB and am now terrified that when I turn it on its going to squeal like it did when it was not biased 🤞

That's ok, the USA is not the centre of the universe.

Kewpie Fuzz. Had a rebuild after the last PCB wasn't working, in hindsight it probably was and I'm pretty sure the relay bypass was fucked. Put a new one in and it's fuzzing. Seems kinda noisy though

Thanks everyone, apparently my cheap multimeter doesn't have a continuity test :cautious: I hit the bottom of the footswitch and the connection between the PCB again with the iron and it is now working on both channels, I really appreciate the brains trust assistance.

Thanks everyone, I'll do some digging tonight when I have it in my hands. That is a bare wire for the output tip but it's not so deep that it should hit a cable tip or anything else, but I'll check it hasn't moved either. I guess if I'm lucky it's just those two pins on the footswitch that...

I tried a quick search to find if this specific issue has been asked but didn't find it. So I sold this pedal, and the new owner messaged me to say that the left side must be engaged to pass signal. If the left side I engaged the pedals left side works, and if the left and right sound are...

I'm trying to build a Kewpie for the second time, I tested the finished PCB on the auditorium and it was working, then boxed it and with relay it's busted again. When turned on it passes a clean signal, the tone, volume and sustain controls affect the clean sound, but it has no gain with the...

Twinface with bc108 and gt402e, 50hfe 192ua and 94hfe 103ua. Those are some BARTs. Sounds good but also yeh it sounds a lot like the Arkhaim. Struggled hard to build this on breadboard beforehand, I am not good at electronics.

Pauper w/ ba282. Only just built this so will see if it makes the cut

Little Green Scream machine Led, stock 4148 and asymmetrical 914...well it will be after I fix up the asymmetrical side since they're currently just three diodes facing different ways.

Adeph Null Troglodyte reverb. Took a big risk on this one, AU$50 for the brick and I'm not really the biggest reverb guy. I don't love the small slapback delay even with onset at minimum but it is actually a nice sound with the sway at around 11oclock.

Simulcast - I really liked my duocast but like relay switching and prefer not to have 1590bb horizontal so figured I'd build the simulcast. MP20a at 61hfe and 70uA leakage.