Search results

Anytime my brother and I thought we got one over on our mother as kids, we'd say "Great minds think alike". To which she'd reply "yes, and fools seldom differ". I don't know if we're great minds or fools, but I did a search for Mini Kliche here because I had this exact issue, and had put NF...

I did solder 2 together to make the value, but I tested them in my component tester before putting them in

The resistors are not touching. Not sure which solder joint that is. Where are you looking? I had reflowed all the joints before posting, so solder should be good

Hi all. Does anything seem like it's out of sorts here. Getting sound in bypass but nothing when engaged. I'm using an A20k pot for tone because I don't have a W20k. Thank you as always

Just finished the graphics on my Guvernator. Love the sound. Absolutely great pedal of you want to rock all the way out!!

Thanks for the response. First, apologies, I guess in my head I was thinking troubleshooting because I wasn't getting much tonal difference regardless of which position the treble switch was in. It all just sounded a little the same. But it probably is more appropriate in the mods section. As...

Thank you, any suggestions on what to change to, or maybe I should socket them and try different values

I just finished the Cujo fuzz build and really like it. If I wanted to get a little more distinction out of the treble boost switch is there any value of the board I could swap out. Doesn't seem like I'm getting a huge noticeable difference on the treble switch, whereas I'm getting a distinct...

OK, so I'm going to build an audio probe to test the circuit next because everything seems to be ok measurement wise. I just want to make sure I have this correct Mono jack - shield lug goes to ground wire/alligator clip - tip lug goes to live wire/220nf cap/probe tip. Then I plug the guitar...

Getting 5v on the drain on Q1, 6.6v on the source on Q4 And thank you for the guidance.

Sorry, forgot to add pic

No subs apart from the FETs. I'm getting 0.7 v reading with the multimeter, but I'll be honest, I'm not 100% sure if I'm doing it correctly.

Using this. Here's the values it's reading

I don't do that stage until I test the circuit on the Micro Proto Board so the jacks and footswitch are not part of the problem. So this is something within the circuit Coda: The schematic calls for J202s, which I don't have, so I used 201s instead. I got them from Tayda, but tested them on my...

Pic of top

Is there anything immediately outstanding as to why I'm not getting anything when active? The only thing I thought was maybe a pot and switch touching, but I put a piece of electrical tape in to stop them. Sound in bypass, but nothing when engaged. I'll post a pic of the top in the reply as...

You can replace it with the B500k, but you're going to lose some of the sweep. A linear pot (A500) will have a steady consistent change as you turn from 1-10. A logarithmic pot (B500) will have the same start and end point for your gain, but much of the turn, from say 1 to 7 (out of 10) will not...

Thanks. That's what I thought when looking at the schematic, but wanted to confirm since I'm still learning (also why I put it in the general questions rather than trouble shooting because I didn't think it was an issue). Again, this thing sounds amazing and everyone should have it in their lineup.

Hello all, I just finished building the Gent Overdrive pedal and I absolutely love it. The only thing I noticed is with the On/Off/On switch, when the pedal is engaged, in the off position of the SPDT it boosts volume significantly over the 2 fail options. Looking at the schematic, it seems...

The Gain pot is a dual linear pot right (B-pot)? So the sweep shouldn't be as noticeable until later in the turn (unlike a logarithmic pot, or A-pot) which has finer tuning throughout the rotation. Have you looked at the schematic to see what caps and resistors are running into it. Maybe you...