Search results

  1. D

    stripboard check

    I just need another set of eyes on this layout. I'd appreciate it. Below is the schematic and I wanna make sure the stripboard layout is accurate. Thanks in advance
  2. D

    PCB Design Help

    I have a pedal that I designed and built using strictly point to point for the circuit. I want to have a pcb version made but have no idea where to start. Is there a service for that? Someone designing the pcb from a schematic and enclosure size?
  3. D

    Potentiometer

    So I’m using a 5KB pot for the fuzz control in my pedal and the fuzz really only kicks in around 9 or 10 on the sweep. Before that there isn’t a whole lot going on fuzz wise. Any suggestions? Would a 5KA work better or a different value?
  4. D

    SOLVED Point to point issue

    Morning. I breadboarded and then built this point to point pedal. I’m only getting bypass at this point. Any ideas? Thanks in advance!
  5. D

    breakout board with stripboard

    So what would I connect to the SW on this breakout board if I'm doing a stripboard circuit? As far as I know, the available wires out of the circuit are 9v, G, In and Out
  6. D

    SOLVED Breadboarding 69 Fulltone

    Hey y’all! Big ask here. But, i’ve been working on this 69 NPN, full tone, fuzz, schematic I bread boarded it, and I get clean bypass sound on both the effect on and effect off. Not sure where I’m going wrong. It seems like there just isn’t any effect at all. I know it’s a lot of wires and...
  7. D

    SOLVED Reeves ZO strip board problems

    I’ve been working on this strip board version of the Reeves ZO. I’ve gotten everything in. I think I’ve followed the strip board diagram correctly, but I’m just not getting anything except for bypass. I know the wiring and stuff is a little messy, but it’d be great. If you could give me some...
  8. D

    Reeves Zo Wiring

    Hey there. I was wondering if someone could me out with the off board wiring for this strip board version of the Reeves Zo. I have it all built and I get bypass signal, but something is up with my wiring to the 3PDT/input output jacks. I’m using the attached wiring diagram. But I was a bit...
  9. D

    Auditorium test and Stripboard

    Just put together this little fuzz face and wanted to test it on the Auditorium Test Board. I’ve never used the board, but thought it was a good time to try. I must be missing something. I think I have everything hooked up correctly and yes. The power and in and out jacks are usually hooked up...
  10. D

    SOLVED LED always on

    So, I built this Aion FX Flare (Fuzz Factory) a few months ago and love the sound. The problem I had was that the LED never came on. Well I revisited the pedal today and realized that the Aion breakout board had snapped the connection between the LEDR and the 9v power wire. Either way, with that...
  11. D

    Fuzz Face Mod

    So, in your opinion, what would adding a B2K pot between R2 (33k) and R3 (470R) do in a fuzz face?
  12. D

    Clear enclosure base

    Does anyone have a source for clear broom plates for pedal enclosures? I’m going point-to-point and would love to have the bottom transparent so you can view the guts of the pedal. Thanks in advance
  13. D

    Breadboarding 101

    Morning!!! So, I've been breadboarding a bit lately and I was wondering what your process is for what path you start with. For example, in a fuzz pedal, do you get the transistors set on the board from input and follow the path to output first and then work on the components that extend from...
  14. D

    SOLVED Trim pot question

    This seems like a silly question, but how do you add a trimpot to a breadboarded circuit? I’m not sure where the three pins should go. Here is the schematic I’m referring to. I don’t have a reference for the 10k trim. So I’m kinda lost.
  15. D

    SOLVED Breadboarding question

    Morning! So I’ve built several pedals at this point and wanted to try my hand at breadboarding a bit. I love the protoboard and tried to setup an EHX LPB-1 as a starter project. I cannot get the “effect” sound out of it. When the board is in the off position or the bypass, I get bypassed...
  16. D

    Aion obscura issue

    So I’ve checked and double checked everything and I can’t figure out why I don’t get an effect sound with this build. Bypass works perfectly though. Any help would be appreciated.
  17. D

    401k issue

    Just finished up the 401k compressor and can’t get any bypass or effect sound. Everything looks okay to me. Any help would be appreciated. Steve
  18. D

    SOLVED 401k drill template

    Morning! Just finished up the 401k compressor build and need to drill the enclosure. I’m not sure there is a drill template for it. Is there a method y’all use to line up the parts or is there another drill template that’ll work? Thanks in advance
  19. D

    SOLVED Input Jack Issue

    I’m kinda lost here. Just finished this Aion Rangemaster build and when I put the guitar cable into the input there’s no sound. If I pull the cable out a bit, it works perfectly. I’ve switched cables. This is the second pedal this is happening on.
  20. D

    Resistor identification

    Hey guys! Attached you will find a pic of the Reeves Twinsound. I'm trying to identify the resistor values, but can't tell some of the colors. I think the ones with the yellow band on the bottom are 470k. Thanks in advance, Steve
Back
Top