Search results

After I originally boxed it up, I just tested to see if the LEDs worked with an underpowered 9VAC adaptor laying around until my 2000ma 9vac power supply came in. When I plugged it in I had a couple of issues. 1. No sound when pedal is engaged (bypass works fine) 2. bypass LED stays on (wired...

This is my absolute favorite chorus. But i will never build another double decker again. (That is after my sagan delay from carcharias) The header pins that most double decker build utilize are so flimsy. I know there are other options out there but the little working space makes it pretty...

So I’ve finally boxed up this build and cannot be happier. It really wasn’t that tough. The only thing that was concerning was the lack of a ground to the output, but i guess its fine. Does anyone have a recommendation for a power adapter for this? I used my friends ac adaptor but it’s only...

This was my first double decker build and it does not disappoint. I am shocked at the size and sound this pedal pushes. I did run into a couple of issues with parts. Firstly, the electrolytics were a bit confusing, mouser lists length and height, and you really have to dig into data sheets for...

I used the header pins recommended in other threads but the clearance is too much, am i doing something wrong it did i get the wrong parts?

I’m about done with building the board but i goofed on the 7 pin. I accidentally soldered on the wrong side, so i had to desolder it and might have possibly damaged it. Is there supposed to be continuity on power pin 1 and power pin 4?

Obviously no one needs 2 king of tones. Both have the same components and both sound pretty identical. I can’t decide whether to keep the big one or the small one. The small one does have better stomp switches (the super expensive soft switch from demont) but they are closer together. If...

I’m not going to lie, my fingers hurt and I am forever grateful for wire strippers. Previously, I used to just use my wire cutter to strip wires; after using my friends strippers, I realized how futile my frugality was. Pedal review Unicab: I built the unicab in conjunction with the L5 preamp...

Im pretty excited to build my brown betty. This is my first "amp in a box" of british gain type, so I made my enclosure art as such. Let me know what you guys think regarding placement and all, any suggestions welcome. Also does anyone know how to make custom potentiometer knobs? I kind of...

I just boxed up the Circulator (Grand orbiter) with some of @Chuck D. Bones mods. I’ll list them below. This pedal sounds pretty good, goes deep and wide. From this Thread “1. Increased R2 & R3 to 2.2M because I like my pedals to have a 1Meg input impedance. C1 was reduced to 47nF because it...

I’m trying to decide between fuzz factory, muffin factory, and a couple others but I’m having a hard time choosing. The only fuzzes i have are ehx op amp and a aion 73 rams head. Never tried any other fuzz. What are your favorite fuzz builds?

I’ve been using a keeley plus for forever but i have to say the optical compressor is definitely different and I like it a lot. It even has a overdrive to it. Any tips on uses and genre?

This one became quite a dog to finish because I fried my footswitches. For those of y’all who soak up the whole lug be careful, you can end up like me. I had to desolder bunch of pins and rewire everything. But man, it looks good.

I lightly soldered this pcb to my foot switch i was wondering if anyone knows of these are compatible?

I think i have the wiring to the stereo jacks incorrect.

Ive looked high and low and even accidently purchased a big b2m potentiometer but it wont fit. I also noticed completed builds had B1M Duals but my pcb has the single B2M. Any help would be appreciated or if you have an extra one :)

This thing sounds killer! I was worried it was going to be noisy but honestly it’s pretty quiet. I added the 25k pot for oscillations with a momentary switch like other folks have built and it rips!

I finished building this a couple weeks ago. It worked totally fine and now it doesn’t and I’m not sure why. Here are the issues 1. When i adjusted the trim pot to find a good spot it would hiss-hiss-hiss in bold mode but not in Script. 2. While i was adjusting the trimmer the led would...

Hello, I just finished building the paragon mini in a gorva and it was a super tight fit. I plugged it up and i got no sound. No bypass, and only the right side’s led works. I have a feeling it’s the switch wiring to the board.. instead of wires i used those breakoff pins that you use for the...

I’m actually kind of baffled. Everything works great but the leds don’t switch on. i used my multimeter and if i hold it against the solder joints they light up fine. anyone have any ideas?