Search results

I've got it up and running now with a little help from some folks on Reddit! Very fun pedal. I've been told by the band that it's a molded Boss OS-2 with a clean blend. Can't say I've ever played an OS-2 before, but it's a surprisingly clean and clear overdrive. I assumed I'd be getting...

Could you point me in the direction of a wiring diagram for offboard LED wiring? I have the standard 3PDT breakout boards, not the one you linked to. Thank you in advance!

A friend of mine bought this at a bands merch table the other day. I've got all the components soldered up at this point, but this is the first PCB im attempting that isn't made by PedalPCB. Ive been using the 3PDT breakout boards for all my builds, so this is new to me. And....i'm a bit lost...

Basically as the title asks. I'd like to build the Kliche Mini special edition but the build doc shows as "coming soon" and it'd been like that for months. So does it use the same parts as the standard Kliche? Am I a-ok to just use that parts list to source everything?

I think it gets a lot of love online because it looks great, and it supports black live matter and trans people. Sounds perfectly fine to my ears, but I don't think the love it gets is primarily off the back of the pedals sound, more so the branding and politics.

Well I guess I'm out of luck then, Robert on here was kind enough to reach out to me and solder some on for me before they shipped, but I have no extras and I don't have any SMD capable tools either. Luckily I have a friend who loves noisy pedals so this one will likely be more appealing to...

I've done that as well and it yields an identical reading

I haven't got a picture of the back of the board. But I'm certain it's clean. I looked over everything and reflowed a few parts to be safe. Cleaned the back up with some isopropyl alcohol afterwards too

Here's the red probe of the test pad and the black on ground. Is my DMM set to the right setting?

You're describing exactly what I did do. It worked fine for the first one, seck d pedal not so much.

I'll have to get to those pictures to tomorrow. But I will show you for sure. Here's a video comparing both of them though.

Just got finished building 2 Chop Shops. The first one I made appears to works just fine, however the second one has far more gain and starts to squeal and oscillate if the gain or sag knobs go to high. These are my first jfet builds, but I'm almost certain I understand the biasing. I am using...

The diagram provided above is to have3 different effects that can run independently yes. I used it, and I can individually turn on and off any combination of the effects as if they were 3 seperate pedals. Hope this helps!

Just wanted to say thank you for this again. Just got it all wired up and it works perfect!

Essentially I want to put a Muff, RAT and Tentacle in this one enclosure and then wire in 3 way clipping sections to the diodes in each board. I've got everything on the PCB soldered in other than the diodes. Am I correct in thinking I can simply run a wire from. either end of D1 on the muff to...

All good Robert 😎 I can take it from there I think. Appreciate the help!

So the middle one would simply have no wires running to it's ins and outs on the top of the PCB?

I might be getting a bit ambitious here, and I'm not even sure if it's possible or not. But is there a way to wire up 3 different effects into 1 enclosure? I want to put a Rat, Big Muff and Tentacle into one pedal. Could somebody please point me towards a diagram of this using the PedalPCB...

Should the clipping LED inside the parentheses light up when signal passes through it in at least one of its clipping modes? Mine doesn't appear to. Also, sounds to me that position 1 & 2 are identical in sound. Is it safe to assume my LED is dead and this is essentially giving me 2 germanium...