Search results

  1. C

    Lowballer Twin distortion setting

    I will try that - thank you!
  2. C

    Lowballer Twin distortion setting

    When I toggle on the distortion it sounds great but it's much louder that the regular setting. What would be the best way to attenuate only the distortion setting?
  3. C

    Replacing a DG Pot with resistors on Frequency Interchange Filter

    Thanks for the reply!
  4. C

    Replacing a DG Pot with resistors on Frequency Interchange Filter

    A friend wants me to make one of these boards to put inside his violin. He wants the LPF to be fixed. We found a setting he liked and I measured the following values: Between terminal 3 and 2 of the top row = .2R Between terminal 2 and 1 of the top row = 19.43k Between terminal 3 and 2 of the...
  5. C

    Dying Battery Simulator

    Oh, I'll try that as well. Thanks!
  6. C

    Dying Battery Simulator

    I'll give that layout a shot and I'll let you know how it goes. Thanks everyone for the replies! I'm still curious - does anyone know how the guy got the one in the video to work so well? Here is another vid with the same setup. He even had to lower the pot value from 10K to 1k. What am is...
  7. C

    Dying Battery Simulator

    They are on lugs 1 and 2 like the diagram and video.
  8. C

    Dying Battery Simulator

    I tried to make one of these but it doesn't work at all. I'm not sure if I need another pair of eyes or if this is a hoax. It seems with a 5k pot this would only go from being the full 9v to 5k of resistance. On my voltmeter that only ends up being .01v difference which is essentially no...
  9. C

    Indicator Light for Eyelet Fuzzrite?

    Thanks for the reply! I thought there might be a way that would include the mounted switch. I ended up going the 3PDT route - it worked (and fit) as well. Pics below. Quick question: why is the volume pot wired backwards in the above diagram? Is that how the original was wired?
  10. C

    Indicator Light for Eyelet Fuzzrite?

    Ahh... the good ole days of sparks flying between your lips and the microphone while playing guitar ! In my day we didn't need no stinkin pyrotechnics.
  11. C

    Indicator Light for Eyelet Fuzzrite?

    I'm making a Fuzzrite from an Amplified Parts eyelet board but want to house it in a regular enclosure. What would be my best approach for adding an LED indicator light so I know when it's on?
  12. C

    Electrovibe

    That link takes you to a switch that is ON - (OFF). Isn't this the one we're looking for: ON-ON? It's less expensive as well: https://www.mouser.com/ProductDetail/633-M2012TNW01-DC
  13. C

    Roboto - no sound when engaged

    Thanks for all the tips. I will check everything that's been suggested.
  14. C

    Roboto - no sound when engaged

    So I finally had a chance to check out everything suggested - zero voltage on pin 7 and no audio on pin 6 or 9 of the HT8950. Nothing on any pin for that matter. Should I get out my solder sucker and recite the mantra "I will never install another IC without a socket" 100 times or is there...
  15. C

    Roboto - no sound when engaged

    The LED does light up when engaged. I will check the measurements on those pins. Thanks for the help!
  16. C

    Roboto - no sound when engaged

    It's a metal enclosure. Bypass works fine and the issue was the same when I took everything out of the enclosure. The jack I have in it is just like in your picture: ground to "sleeve" - in and out from the footswitch to "tip".
  17. C

    Roboto - no sound when engaged

    Thanks for the replies. I will check those.
  18. C

    Roboto - no sound when engaged

    My first PedalPCB project - I actually made two of these and both do not pass audio when engaged. Hopefully another pair of eyes can see if I did something incorrectly. I didn't have sockets for an 18 pin IC so I soldered it directly to the board. Maybe the two HT8950s are bad? They were...
Back
Top