ferdinandstrat
Member
I tried hooking POT0 to the control input of the Tap Tempo block and the Tap Tempo out to the Delay Time of a Delay block and I get nothing, any ideas?
For those who use the SpinCAD designer - How do I use the Tap Tempo block?
- Thread starter ferdinandstrat
- Start date
Maybe you need the other nodes (ramp and latch) hooked to something. Here's the source code for the tap tempo block FYI.
github.com
I don't really feel like sorting through all that right now to figure out how to use the block. But, it says the author is "slacker". So, I'm guessing the block is supposed to do his tap tempo delay code from his Babelfish project.
github.com
SpinCAD-Designer/src/com/holycityaudio/SpinCAD/CADBlocks/TapTempoCADBlock.java at master · HolyCityAudio/SpinCAD-Designer
SpinCAD Designer is an open source Java project which allows creation of patches for the Spin FV-1 audio DSP chip. - HolyCityAudio/SpinCAD-Designer
github.com
I don't really feel like sorting through all that right now to figure out how to use the block. But, it says the author is "slacker". So, I'm guessing the block is supposed to do his tap tempo delay code from his Babelfish project.
GitHub - slackDSP/Babelfish: Spinsemi FV-1 based pedal ideas
Spinsemi FV-1 based pedal ideas. Contribute to slackDSP/Babelfish development by creating an account on GitHub.
github.com
ferdinandstrat
Member
Maybe you need the other nodes (ramp and latch) hooked to something. Here's the source code for the tap tempo block FYI.
SpinCAD-Designer/src/com/holycityaudio/SpinCAD/CADBlocks/TapTempoCADBlock.java at master · HolyCityAudio/SpinCAD-Designer
SpinCAD Designer is an open source Java project which allows creation of patches for the Spin FV-1 audio DSP chip. - HolyCityAudio/SpinCAD-Designer
I don't really feel like sorting through all that right now to figure out how to use the block. But, it says the author is "slacker". So, I'm guessing the block is supposed to do his tap tempo delay code from his Babelfish project.
GitHub - slackDSP/Babelfish: Spinsemi FV-1 based pedal ideas
Spinsemi FV-1 based pedal ideas. Contribute to slackDSP/Babelfish development by creating an account on GitHub.
I thank you quite a lot for this...but sadly it doesnt tell me much, I am not too familiar with the source code itself
ferdinandstrat
Member
So its an incomplete block? Or do I just hook it up instead of a pot? Is there something that should go between the two? I am sorry for the barrage of questions I am just a total noob.
Digital Larry
Active member
The tap tempo block was supplied by "slacker" and was part of his babelfish project over at diystompboxes.com.
Ah take a look at the schematic, esp. the wiring of the signal to POT2. There's your answer.
github.com
The "latch" and "ramp" outputs of the tap tempo block were just used for debugging.
DL
FV-1 Multi effect full forum project ready to go. (ShimmerVerb Also) - Page 14
FV-1 Multi effect full forum project ready to go. (ShimmerVerb Also) - Page 14
www.diystompboxes.com
Ah take a look at the schematic, esp. the wiring of the signal to POT2. There's your answer.
Babelfish/babelfishschem.jpg at master · slackDSP/Babelfish
Spinsemi FV-1 based pedal ideas. Contribute to slackDSP/Babelfish development by creating an account on GitHub.
github.com
The "latch" and "ramp" outputs of the tap tempo block were just used for debugging.
DL
Last edited:
Similar threads
