Recent content by nichgriff

  1. N

    Magnetron LEDs not working

    So weird thing - I did remember I switched colors of LED and apparently I have a whole batch of yellow LEDs that do not work. Welp. Red is good to go though!
  2. N

    Magnetron LEDs not working

    Hello! Back again with another stupid question! Both LEDs aren’t working on my magnetron delay. They were both working when I had them setting in place testing the circuit but neither work now that they are actually in the enclosure. Assuming it is likely being sent to ground somewhere (like...
  3. N

    Informant Input Grounded

    I think that may have been it. Got it working right after I posted this but forgot to return to post. Cleaned it with some alcohol and reflowed all the connections and that did the trick!
  4. N

    Informant Input Grounded

    Hello! I just finished up the informant drive and the input is going to ground. I’ve switched jacks and it’s still doing it. It’s my first time doing buffered bypass but I bought one of the pedalPCB buffered bypass daughter boards. Will take more and better photos after dinner time. Thanks!
  5. N

    Informant Overdrive - No Signal (Buffer or Effect)

    Should there be continuity at all of these places?
  6. N

    Which digital platform?

    Hello friends! I'm sorry if this is repetitive, but I'm torn on which digital platform to begin with for pedals. Daisy seems more powerful than FV-1 but FV-1 seems a bit easier for a beginning, as well as there even being the stereo platform coming soon from PedalPCB. I have programming...
  7. N

    War Scythe Issue(s)

    Oh - and lastly - LEDs don’t seem to be working. I don’t have them soldered in yet but I usually don’t and they still turn on when I have them pinned in place.
  8. N

    War Scythe Issue(s)

    Looking at the picture - I see a few cold shoulders and places that need more solder. I’ll get to that right after bed. Sometimes stepping away is helpful and looking at pictures shows what my eyes missed haha
  9. N

    Quick Tip For Testing - Noobs PLEASE READ

    Ha! I literally did this with a new build last night and was so sad. Until I realized I had the board upside down so when I thought volume was maxed it was actually turned all the way down. Doh!
  10. N

    War Scythe Issue(s)

    Hello friends! I have a few questions and wanted to get some feedback: 1) When engaged, the ungula side sounds basically the exact same as my clean signal, which I find odd. Transistors are socketed and not the most secure right now but the scythe side is the same which is working. I have two...
  11. N

    Green Russian Muffin Fuzz

    Okay - this is probably the dumbest question ever posted on this forum... Which pot is which on the muffin fuzz?? It appears to be (looking at pedal as if it were done) - top left is volume, top right is sustain, bottom is tone but I'm too new at this. How can I tell for sure besides tracing...
  12. N

    Green Russian Muffin Fuzz

    This is all super helpful - thanks! I think I'm going to go A100k for volume and the other two B100k.
  13. N

    Mantle Fuzz (MXR Blue Box) voltages

    Ha! My amp has reverb too which is always on. OBSESSED. I was considering building a dual build with the ghost echos and space spiral (whatever they're called on here) - I think it would be a crazy ambient machine!
  14. N

    Resistor value importance

    So if I'm building a fuzz that calls for a 2k resistor - using a 2.2k isn't out of the realm of possibilities but could cause issues depending on where it is in the circuit?
  15. N

    Mantle Fuzz (MXR Blue Box) voltages

    My issue is of the 6 pedals I have - 3 are reverbs! Haha haven’t built one yet because of that but it’s my favorite and most used effect.
Back
Top