Search results

Awesome thank you for your help.

I'm currently working on modding a Pitch Witch. I have one built and it works great. But I assembled it on my breadboard and it works, but there's a loud clicking with the LFO. I've never really messed with anything using an LFO before, so is there something obvious that I'm missing?

I have a similar issue. I purchased some GT404B's form small bear, tht should read hf3 80-140. However, when I plug them into my multimeter NPN section, the readout is 1 for the 20 I've tested. Am I doing something incorrectly, is my mulitmeter faulty, or did I just get a batch of duds...

I just wrapped up an ocelot, and it seems Ok except the volume of the 2 octaves are very low. The normal volume works fine, just the octaves are very low comparatively. I’ve never played an original to compare this to, so I’m wondering if there’s an issue somewhere, or if the lower volume is...

Not sure if this will work, or be good/useful but I figured I would ask before I did something that could cause damage. I had an idea to add a sag feature to a Tone Vendor to simulate a dying battery. I was going to add a b10k pot and a 220uf capicator between the 1n5817 and pin 1 of the...

Yeah that one also has the lower output

I recently build an OCD and Rat in 1 enclosure with an order switcher, and everything is working as it should. However, the output seems rather low. Where a normal ocd would be at 12 o’clock, mine has to be pushed to almost 4 to reach the same volume, and some of the high end that’s in the...

I'm working on a Distortion 250 on my breadboard and want to make some mods. One complaint I have is that the gain pot is a B1M and as it sweeps it doesn't change much then gets real dirty in the last 10%. If I want to make the sweep more gradual, would I change the value of the pot or the...

Got it all set with the 4pdt. Thanks for all the help!

So I found that I had an extra 4PDT. What lugs should I solder the LED to?

Is it possible to just run a wire from the positive of the DC through a 4.7K resistor into the anode of an LED and connect the cathode to one of the pins of the 3pdt that sticks up through the switch pcb? That way I don't have to order any more parts? If so, which pin would I use?

I'm doing a 2 in 1 pedal with an ADHD and Muroidea and I have a 3PDT switch pcb to swap the order. Is there a way to incorporate an LED so that you can tell the order of pedals when they're both engaged? If so, how would you go about wiring that? thanks.

I did it from the schematic from the distortion 250 build docs

Hey, it’s my first time using a breadboard, and I’m trying to tinker with a distortion plus circuit. Everything is wired up and it seems to be working, however, when I get the volume pot all the way up, it kills the signal. Any idea what may be causing this? Thanks in advance.

Just curious what some of you have been using to do artwork on your pedals. I've been going the JHS route and using rubber stamps with stazon ink, but I'm interested in trying other things. Any suggestions?

This may be a dumb question.... so I understand the difference between A B and C pots, but what decides the value of individual pots (example: A100k or A50k) in circuits? what would happen if you were to use a B1M in place of a B10k? thanks in advance!

thanks!

Does anyone have any experience using a more available replacement for a 2n1711? What would you recommend? Its for a Cross Contaminator (Dirt Transmitter)

thanks

I am putting together a Twin Face, and I was curious if I could use a 4pdt latching footswitch in place of a 4pdt toggle to be able to switch settings mid song. In my brain I think it'll work, but I just wanted to put it out there before I did something crazy wrong. thanks