Abyss - LDRs - 2 ?'s

BeeSharp

BeeSharp

Active member
I recently built the madbean glasshole, which is a mu-tron phaser. Those instructions say to mount the LDRs flat. I was looking at the Jam pedals Retrovibe and some other folks' builds and I see the LDR's standing up instead of flat. Which is correct for the Abyss? and what LED to use? I know that 620nm is Red, so does the Tayda clear red 5mm work ok? Thanks!
 
The angle of the LDR is just a personal preference. Considering the whole thing will be enclosed in the case when done, any light bleed at that point would be negligible. The use of the yellow reduces the "efficiency" of the LDR's reception by a given percentage and I believe that is by design. Perhaps by being prepared to swap out a red LED for the specified yellow LED will give an opportunity to hear any difference. Though I doubt any real difference will be heard. Just my 2¢.
 
I did mine with the LDRs pointing straight at the LED and it sounded awful. I think the resistance was going too low at full brightness. I backed them off a ways and everything sounded much better and had a more useable range. So "maximum efficiency" isn't necessarily what you want here. If you point the LDRs straight up, you'll get the bounce from the inside of the enclosure (assuming it isn't matte black on the inside), so that would probably work too.
 
I built the Glasshole recently and really like it. I used Tayda LDRs and stood them up in a circle around the LED.
 
Just want to check something -
I can't track down an LDR with the same dark/light specs as the Tayda KE 10720.
Best I can locate locally via Jaycar hits the dark resistance (0.5M), but the light range is 2.8K to 8.4K. Will this be suitable, or am I waiting for a delivery from Tayda or Altronics?

Also, can't locate MPSA18 locally, would BC5089 or MPSA13 be suitable?
 
blackops said:
Just want to check something -
I can't track down an LDR with the same dark/light specs as the Tayda KE 10720.
Best I can locate locally via Jaycar hits the dark resistance (0.5M), but the light range is 2.8K to 8.4K. Will this be suitable, or am I waiting for a delivery from Tayda or Altronics?

Also, can't locate MPSA18 locally, would BC5089 or MPSA13 be suitable?
Click to expand...
5089s are usually swappable with MPSA18s. Socket and test of course.
 
blackops said:
Just want to check something -
I can't track down an LDR with the same dark/light specs as the Tayda KE 10720.
Best I can locate locally via Jaycar hits the dark resistance (0.5M), but the light range is 2.8K to 8.4K. Will this be suitable, or am I waiting for a delivery from Tayda or Altronics?

Also, can't locate MPSA18 locally, would BC5089 or MPSA13 be suitable?
Click to expand...
Where are you located?
 
blackops said:
Hot damn.
AND proper pcb mount pots, AND cheaper than Jaycar.
Click to expand...
The 9mm pots are not suitable for PedalPCB builds.
I thought you would have known PedalParts Australia:

TRANSISTORS : Pedal Parts Australia, DIY Guitar & Effect Pedal Parts

Pedal Parts Australia : TRANSISTORS - SWITCHES KNOBS ENCLOSURES CONNECTORS POWER CABLES POTENTIOMETERS LED's & BEZELS WAH PARTS BOSS PARTS GUITAR PCB GUITAR PCB KITS IC'S TRANSFORMERS RELAYS SEMICONDUCTORS CAPACITORS RESISTORS OPTOCOUPLERS ACCESSORIES CLEARANCE GUITAR PCB NOSTALGITONE ecommerce...
www.pedalpartsaustralia.com www.pedalpartsaustralia.com

https://www.pedalpartsaustralia.com/index.php?main_page=index&cPath=12_114
 
You must log in or register to reply here.

Similar threads

J
Phase 2 LDR’s
Replies
0
Views
77
Jer
J
T
feedback in a 2-stage phaser?
Replies
3
Views
126
jimilee
jimilee
J
Phase 2 - LDR’s - Photoresistors
Replies
12
Views
337
Jer
J
M
Red Herring #2 (Menatone Red Snapper)
Replies
1
Views
391
KT88
KT88
Fingolfen
A Famous 1980's Vintage Chorus - With a Purple Dinosaur??? (AionFX Lithium)
Replies
5
Views
608
Fingolfen
Fingolfen
Back
Top