Missing Build Docs / Schematics

[tremolowe]

SCABBARD
---------------------
4 100R
1 1K
2 2K2
1 4K7
3 10K
1 20K
3 47K
3 1M

3 1n
1 3n3
2 10n
3 47n

3 1u MLCC
* Filtering/decoupling, use MLCC

11uF E
4 4u7
2 100u

2 D9B
1 5817

4 A100K

2 OP07

1 8.2uH
* https://www.taydaelectronics.com/8-2uh-inductor-ec24.html

1 ON/ON

I have the drill coordinates for tayda if you want them.

I'd like those coords, if you please. Scabbard is a definite future build from me! I'd love to see the schem for it too whenever that drops.

 

[zeropluszero]

Tayda Electronics Drill

Tayda Electronics Drill Designer for custom enclosures.

drill.taydakits.com

Scabbard (rev 1?)
Obviously check the diameter of your holes, but my PCB has dropped right into this.

 

[tremolowe]

Tayda Electronics Drill

Tayda Electronics Drill Designer for custom enclosures.

drill.taydakits.com

Scabbard (rev 1?)
Obviously check the diameter of your holes, but my PCB has dropped right into this.

Thank you very much, I appreciate it. I'd like to get one printed and drilled when I get around to that project so this is very helpful.

 

[Mbens11]

Thanks!

 

[StickyDingo]

@Robert - Synopsis schematic, pretty please?

 

[tcpoint]

Is there a drill template for the Salesman? I'm too lazy to make one.

 

[Robert]

@Robert - Synopsis schematic, pretty please?

It's in the doc.

https://docs.pedalpcb.com/project/Synopsis-PedalPCB.pdf

Is there a drill template for the Salesman? I'm too lazy to make one.

https://docs.pedalpcb.com/project/drill/1590BB-DrillTemplate-Salesman.pdf

 

[Phil hodson]

Hi @Robert. Any chance of a drill temp for the 4 tap DC convertir/isolator. And the length of the standoffs requires. Thanks.

 

[drumstiku]

Pardon if I’ve missed a previous post but could we get build docs for the Headphone Amplifier?

 

[VanWhy]

@Robert will we have build docs soon for the Acrobat Parametric Distortion? If not maybe a BOM list?

 

[Mr. Strypes]

Hey, everybody! Are there build docs for the Salesman (Lerxt) Overdrive posted somewhere? Or a BOM perhaps?
Thanks in advance!

 

[Robert]

Hey, everybody! Are there build docs for the Salesman (Lerxt) Overdrive posted somewhere? Or a BOM perhaps?
Thanks in advance!

Salesman Overdrive

https://www.pedalpcb.com/product/pcb662/

forum.pedalpcb.com

 

[DeadAirMD]

Hi @Robert. Any chance of a drill temp for the 4 tap DC convertir/isolator. And the length of the standoffs requires. Thanks.

Definitely curious about the sizing for the standoffs. Already drilled the enclosure and the board is pretty snug, but would like to figure out what size screw/standoff/ mounting hardware fits those holes

 

[Nic]

@Phil hodson @DeadAirMD Here is the info for the standoff. They were spot on for me but I did my own drilling template.

Here was his answer to me.
Post in thread 'Is this the correct orientation ?' https://forum.pedalpcb.com/threads/is-this-the-correct-orientation.21161/post-268365

 

[Mr. Strypes]

Salesman Overdrive

https://www.pedalpcb.com/product/pcb662/

forum.pedalpcb.com

Thanks, Robert! You're awesome, bro!

 

[Fama]

A couple of Tayda drill template questions:

I assume the Antithesis is just the basic 4 knob layout, so pre-drilled boxes would work? Similarly Bellum Fuzz MK. II is a 3 knob.

But how about the Abyss? It doesn't seem to be the normal 5 knob layout, are there measurements somewhere or a Tayda drill template? I didn't find any. I can always measure the PCB but I don't trust myself to get it 100% right. Better than nothing else if it comes to that.

Similar question for the Fuzz Cadet, I do have a drill template for the Simulcast which I think is similar? I think I had some slight issues with the Simulcast when I built it, but nothing I can't fix afterwards, so if there's nothing better I can use that one (assuming the template is similar).