knobToucher
Member
Just wanted to know if the Tearjerker Wah will fit in one of the BYOC Wah enclosures? They look very nice..
buildyourownclone.com
Tearjerker enclosure
- Thread starter knobToucher
- Start date
Robert
Reverse Engineer
Those might be the same ones offered by Smallbear, but powdercoated.
If they're the same spec as a Crybaby (and the description seems to imply that they are) then they should work.
Nostradoomus
Well-known member
I always found it easier to just wait until a crybaby comes up on Craigslist for 30 bucks haha. Then you get the pot too!
Did you end up using this enclosure? I'm about to start a TearJerker build and I'm looking for a good enclosure.Just wanted to know if the Tearjerker Wah will fit in one of the BYOC Wah enclosures? They look very nice..
Build Your Own Clone Message Board • Login
Jovi Bon Kenobi
Well-known member
I had a panic moment and just wanted get some clarification. Did I order the wrong enclosure from smallbear? It says "expression shell". I ask because there is no square hole for the DC jack it it and thats what I also have.
This is what I have and the only wah-type enclosure I could find on the smallbear site.
smallbear-electronics.mybigcommerce.com
This is what I have and the only wah-type enclosure I could find on the smallbear site.
Expression Pedal Shell Kit
New England's source for guitar pedals, pedal parts and electronics.
smallbear-electronics.mybigcommerce.com
I just reread the product page for this one and it says designed for the expression pedal shell. So you're good. And now I know what to buy also!
Jovi Bon Kenobi
Well-known member
Woops, thanks. Buy some primer and paint while you're at it ?
Fyi, there is no square hole for the DC jack on mine. I will check to see if a standard innie fits.
Fyi, there is no square hole for the DC jack on mine. I will check to see if a standard innie fits.
knobToucher
Member
Unfortunately I haven’t had a chance yet! Will definitely give it a go eventually. I have such a massive backlog of completed projects to be boxed! Good luck, are you going with the small bear one or are you going to give the BYOC enclosure a try?
I think I’ll give the Smallbear one a try, since I know it will fit. Assuming the DC jack works with it. But I do like the look of the BYOC one better. Maybe I’ll get them both! I’ll post the completed one once I’ve had a chance to put it together.
Jovi Bon Kenobi
Well-known member
Here's the Smallbear expression enclosure
As you can see, the PCB mount DC jack will align just right but it might look weird with that round hole. If you're cool with it, have at. The Lumberg innie jack in the photo won't fit in the hole, but would if you drilled it about one step further. You'd just need to run some wires to the PCB.
As you can see, the PCB mount DC jack will align just right but it might look weird with that round hole. If you're cool with it, have at. The Lumberg innie jack in the photo won't fit in the hole, but would if you drilled it about one step further. You'd just need to run some wires to the PCB.
Last edited:
Awesome. Thanks for that picture. I could definitely live with but may try drilling it out or seeing if one of the smaller jacks that I use fits. But do you need the 3 prongs on the jack to wire it to the board or could I wire one like this to the board? https://www.pedalpcb.com/product/dcjack1/
Jovi Bon Kenobi
Well-known member
Too small. It freely floats right through the wah enclosure hole
Nostradoomus
Well-known member
You could use a fender washer but it’d look silly 
