What about trying to turn them On & Off!!!
It would almost work if you used one upright & the one next door in the standard position???
What’s on *YOUR* workbench?
- Thread starter Bricksnbeatles
- Start date
It would almost work if you used one upright & the one next door in the standard position???
SillyOctpuss
Well-known member
Dang they look good. Love the gold dude
steviejr92
Authorized Vendor
I had miscalculated and had one odd enclosure by itself so I decided to do something I hadn’t done before! I like it too but next time I’m going to add clear coat to both bottom and top.
steviejr92
Authorized Vendor
Woah…I need to get some copper vein! I have a brown/tan in that hammer finish but I don’t think that would look right…the copper is better looking in my opinion.
SillyOctpuss
Well-known member
WTF I've just seen this. My two favourite colours in one place. Like @Feral Feline can I add an enclosure in this colour to my order too please?
steviejr92
Authorized Vendor
I already got you covered! I remembered you wanted a purple enclosure!
SillyOctpuss
Well-known member
steviejr92
Authorized Vendor
I still need to take individual pics for each color in the Photo Booth but here’s the batch in its entirety!
Feral Feline
Well-known member
You could just turn your 125b's with top mounted jacks on their side & transfer the Pots & footswitch with led there as well, now there is some space saving!!!
View attachment 67615
I have the PCB and a Pre-drilled enclosure. I thought of drilling another hole by the jacks so that at least it's only two sides that are occupied.
Either that or drill another hole on the south wall and stick the stomp-switch there, making it a kick-switch — will need the insanely strong mushroom-headed pedalboard tape for that config.
Actually, I recently found the decor for my Bear Boost Plus to help hide the stupid sides configuration.
Feral Feline
Well-known member
I still need to take individual pics for each color in the Photo Booth but here’s the batch in its entirety!
IMPRESSIVE!
Those three in the top right corner are MINE! I'm sure of it.
Or maybe the orange, copper, and (skip the blue) purple in the top LEFT corner...
steviejr92
Authorized Vendor
You were right with the top 3 on the right!
IMPRESSIVE!
Those three in the top right corner are MINE! I'm sure of it.
Or maybe the orange, copper, and (skip the blue) purple in the top LEFT corner...
drgonzo1969
Well-known member
Those knobs are killer.
Fama
Well-known member
Oh man, it feels good to find a clear culprit. I was troubleshooting the bypass signal being bad so I whipped out a tone generator plugin and a frequency analyzer plugin to figure out what was happening. I knew I was losing a couple of dB (3dB more or less), but I didn't realize this was also happening without the frequency analyzer:
I then started figuring out where it was happening, and it was happening right at the input to a lesser extent, and definitely before the JFET.
Buuuut then I noticed one of the diodes before the JFET was the wrong way around so just a good check for errors would have also cleared this up. So not an issue with the JFET at all.
Culprit:
I then started figuring out where it was happening, and it was happening right at the input to a lesser extent, and definitely before the JFET.
Buuuut then I noticed one of the diodes before the JFET was the wrong way around so just a good check for errors would have also cleared this up. So not an issue with the JFET at all.
Culprit:
SillyOctpuss
Well-known member
IMPRESSIVE!
Those three in the top right corner are MINE! I'm sure of it.
Or maybe the orange, copper, and (skip the blue) purple in the top LEFT corner...
I think we put in pretty much the same order
Passinwind
Well-known member
Four of the five boards I need to finish up the new EQ/HPF/piezo/magnetic blend pedal for my dojo:
There's gonna be a whole lot of outboard wiring to work through, just the way I like it!
There's gonna be a whole lot of outboard wiring to work through, just the way I like it!
DGWVI
Well-known member
Didn't realize until I'd used them, that my new stamps are the Claire's font (xor-cist)
Also, except for big witch hats, I'm outta knobs
benny_profane
Well-known member
That’s your Futura Bold archetype?