Missing Build Docs / Schematics

[Billyhank]

Is there a drill template for the Breakroom or a comparable template that would work?

 

[Nostradoomus]

Is there a drill template for the Breakroom or a comparable template that would work?

https://forum.pedalpcb.com/threads/pedalpcb-chop-shop-v2.22224/ should work

 

[Billyhank]

https://forum.pedalpcb.com/threads/pedalpcb-chop-shop-v2.22224/ should work

Thank you!

 

[Macca]

Hello, is there a Tayda drill template for the Mofeta Preamp?

 

[Robert]

Hello, is there a Tayda drill template for the Mofeta Preamp?

The standard 6-knob template should work.

Tayda Electronics Drill

Tayda Electronics Drill Designer for custom enclosures.

drill.taydakits.com

 

[TillMack]

Hey, I’m in search of the build documents for the Liquid Crystal Fuzz.
Thanks in advance

 

[Robert]

Hey, I’m in search of the build documents for the Liquid Crystal Fuzz.
Thanks in advance

It's identical to the "Chelsea" variant in the Muffin build docs:

https://docs.pedalpcb.com/project/MuffinFuzz-PedalPCB.pdf

 

[fontoponto]

Yes, of course. I've been away from my bench for a few days so I have some catching up to do, but I'll get it posted for you.

About the Acrobat -> bump

 

[disssa]

Hi @Robert
Any chance we could get a schematic for the MicroXLR Output?

 

[jmsiener]

Hi @Robert
Any chance we could get a schematic for the MicroXLR Output?

Same subject but different request: would love just a drill template for the MicroXLR. I’m never too worried about drilling Pots and what not and most of the time the dimensions are similar from pedal to pedal. This XLR gives me anxiety because of the two mounting screws and I’d like to modify some existing pedals so fubar’ing a perfectly good enclosure is another layer of anxiety.

Thanks!

 

[benny_profane]

Same subject but different request: would love just a drill template for the MicroXLR. I’m never too worried about drilling Pots and what not and most of the time the dimensions are similar from pedal to pedal. This XLR gives me anxiety because of the two mounting screws and I’d like to modify some existing pedals so fubar’ing a perfectly good enclosure is another layer of anxiety.

Thanks!

Reference the device datasheet.

 

[Morbidpale]

Believe me I tried. Im sure it's somewhere obvious.
Is there a schematic for the
Basic Relay DPDT switch? Non latching. Im soooo confused trying to figure this out.

 

[Robert]

Is there a schematic for the Basic Relay DPDT switch?

 

[Morbidpale]

Much appreciated!

 

[DGWVI]

Any chance we could get a Low Tide Mini build doc, or at least a resdef layout?

 

[jmsiener]

Reference the device datasheet.

Sounds like a great way for me to fubar a perfectly good enclosure. It’s why I made a request.

 

[benny_profane]

Sounds like a great way for me to fubar a perfectly good enclosure. It’s why I made a request.

Oh man you’re right what was I thinking.

 

[Robert]

Same subject but different request: would love just a drill template for the MicroXLR.

Try this, double check it before drilling.

@benny_profane is correct though, the drill template could vary depending on the XLR jack used. The attached template is for the XLR jack from Tayda, if you use a different jack you'll need to adjust the coordinates according to the datasheet.

https://www.taydaelectronics.com/chasis-3-pin-xlr-male-plug-connector-gold-plated.html

https://www.taydaelectronics.com/datasheets/files/A-3924.pdf