Nobelium

[Erik S]

I’ve joined the cult!

I don’t play much bass, but it sounds nice as a DI with my baritone.

Keepin it DIY with some tricky drilling and Posca pens as usual. The lighting in my shop made the color look all screwy, but it’s regular Tayda cream with a matte clear coat.

So far I’ve been running it off one of the 500ma 9v outputs on my voodoo lab 3plus. Recommended minimum is 600ma…

I think I could run it on the 12v 1a, or pull one of the tubes if I’m just running the xlr to lower the draw, but I need to do some more reading to try and figure out the best option.

 

[vigilante398]

Looks great!

12V 1A is going to be a better option than 9V 500mA, but obviously if you're not using the 1/4" output then removing V2 is also an option.

 

[Erik S]

Looks great!

12V 1A is going to be a better option than 9V 500mA, but obviously if you're not using the 1/4" output then removing V2 is also an option.

Guess I don’t have to do some more reading after all. That was faster than asking chatGPT!

Thanks Nathan.

 

[Aleph Null]

This looks great! I'd love more details on your drilling process: was it all drill press, or did you do some machining?

 

[Guardians of the analog]

This turned out great. Welcome to the cult

 

[Erik S]

I'd love more details on your drilling process: was it all drill press, or did you do some machining?

Oh yeah, tons of respect for the folks drilling rows of holes and fileing them into slots by hand, but I’m doing it the easy(ish) way with an old manual mill.



For this little batch of c2ce stuff I set table stops to cut the longest slot, then spaced off the stops with a series of gauge blocks to cut the smaller slots. It wasn’t bad once I got in the flow, but I did mess one up and then tried to make it look intentional.



The diamond shapes was my plan for a simpler design after doing curved slots in my last one.

 

[Harry Klippton]

Oh yeah, tons of respect for the folks drilling rows of holes and filling them into slots by hand, but I’m doing it the easy(ish) way with an old manual mill.

View attachment 112771

For this little batch of c2ce stuff I set table stops to cut the longest slot, then spaced off the stops with a series of gauge blocks to cut the smaller slots. It wasn’t bad once I got in the flow, but I did mess one up and then tried to make it look intentional.

View attachment 112767

The diamond shapes was my plan for a simpler design after doing curved slots in my last one.

View attachment 112769

Yoooooooooooo
Also I have that same Kennedy tool chest on top

 

[Erik S]

Also I have that same Kennedy

Classic 7 drawer! Can’t beat it.

I even made an attempt at re-felting that one.

 

[Harry Klippton]

Classic 7 drawer! Can’t beat it.

I even made an attempt at re-felting that one.

View attachment 112781

I've got a bottom unit for mine too. I'll send you a picture tomorrow. I'm it going out there now

 

[genXslacker]

I did mess one up and then tried to make it look intentional.

They look like lava lamps. Just find a way to work that into a theme and you're golden. They definitely look intentional.

 

[Erik S]

They look like lava lamps. Just find a way to work that into a theme and you're golden. They definitely look intentional.

I don’t really do graphics or themes unfortunately. If I did, my childish sense of humor would steer me toward a butt plug theme, so it’s probably for the best.

 

[genXslacker]

I don’t really do graphics or themes unfortunately. If I did, my childish sense of humor would steer me toward a butt plug theme, so it’s probably for the best.

We are cut from the same cloth.

 

[Harry Klippton]

Classic 7 drawer! Can’t beat it.

I even made an attempt at re-felting that one.

View attachment 112781

It's heaped up with other crap but here it is. The lowest section has a door that slides out and folds down. and I've got a cover for the top drawer that clicks into place when the top lid is closed. Planning to clean up this space this summer maybe

 

[andare]

Guess I don’t have to do some more reading after all. That was faster than asking chatGPT!

Thanks Nathan.

And Nathan won't lie to flatter you or appease you!

 

[Erik S]

The lowest section has a door that slides out and folds down. and I've got a cover for the top drawer that clicks into place when the top lid is closed.

Full Kennedy stack is hott.

Planning to clean up this space this summer maybe

If the mower service center gets a glow up I expect updates.