VIIB

[Bio77]

Man, this pedal fricken rocks. I think Bugg nailed this one. The relay bypass is elegant and works perfect.

I think classic mode is required, in true bypass mode you can hear the pedal come in and it kills the vibe (see what I did there ). Classic mode is dead silent.

I set the clock at 120kHz, in case anyone was looking for that ( I couldn't find it on the forum).

 

[benny_profane]

Looks great! This stylistic direction is really going well. Beautiful execution on the boards.

Btw, what is that LED bezel?

 

[dawson]

All hail Bio77!

 

[Harry Klippton]

Good lord your graphic styling always kills me

 

[cooder]

Fabulous inside out, killa build again!

 

[fig]

Smooth as silk sir!

 

[delayed]

Is there a place to get the relay cheaper than mouser?

 

[Barry]

Nice build!

 

[Bio77]

Thanks fellas! The bezel is from Tayda.

Is there a place to get the relay cheaper than mouser?

Yes, I use these, they are cheaper:

https://www.mouser.com/ProductDetail/551-EA2-5SNJ

 

[delayed]

Thanks for the link

https://www.mouser.com/ProductDetail/551-EA2-5SNJ

 

[delayed]

A few more questions if you don’t mind.

Did you use a 470k trimmer or a 500k?

Did you use a 200pf or 220pf for the 200pf position?

SKU A-3208

250K OHM Anti-Log Taper Potentiometer PCB Mount Round Shaft Dia: 6.35mm

ALPHA - Get It Fast - Same Day Shipping

www.taydaelectronics.com

This the correct c250k pot?

And finally what Led did you use? 5mm

Bi-color LED Red/Green 5mm Common Cathode

Get It Fast - Same Day Shipping

www.taydaelectronics.com

 

[Paradox916]

That’s super clean man! nice job!

 

[Bio77]

A few more questions if you don’t mind.

Did you use a 470k trimmer or a 500k?

Did you use a 200pf or 220pf for the 200pf position?

SKU A-3208

250K OHM Anti-Log Taper Potentiometer PCB Mount Round Shaft Dia: 6.35mm

ALPHA - Get It Fast - Same Day Shipping

www.taydaelectronics.com

This the correct c250k pot?

And finally what Led did you use? 5mm

Bi-color LED Red/Green 5mm Common Cathode

Get It Fast - Same Day Shipping

www.taydaelectronics.com

The pot and LED are correct. You can use a 500K. I used a 200p.

 

[delayed]

I snoozed on the relay while building up an order due to shipping fees. Is there another replacement for the relay?

 

[Bio77]

I snoozed on the relay while building up an order due to shipping fees. Is there another replacement for the relay?

I don't know off hand, I found the one I use by searching mouser with the specs of the panasonic relay. I know that 4.5V will also work. Just make sure it's latching. Tayda has one but it's non-latching and won't work.

 

[Diynot]

https://www.mouser.com/ProductDetail/KEMET/EA2-5SNJ?qs=rjnFDYRVT0pyNrkQASyvGA%3D%3D

@delayed This is the one that was suggested when I asked and it works. I did find some of the Panasonic on antique electronic supply awhile back

 

[fig]

https://www.mouser.com/ProductDetail/KEMET/EA2-5SNJ?qs=rjnFDYRVT0pyNrkQASyvGA%3D%3D

@delayed This is the one that was suggested when I asked and it works. I did find some of the Panasonic on antique electronic supply awhile back

FYI - Those are out of stock

 

[fig]

Search | Amplified Parts

www.amplifiedparts.com

 

[JamieJ]

This is pretty much as good as it gets @Bio77 !!!

 

[delayed]

Tried a couple different relays. Both seem to work. Tayda item A-1169 and NEC Japan EA2-5SNJ.