What's in the mailbox? 📬 📦

Harry Klippton said:
I need to buy so so so so many cables 😭
Click to expand...
Build them!
Check markertek and BTPA for cable.
SBP has a bunch for Neutrik XLR copies on sale for cheap right now too! Bet you can build a better cable for half the price or better vs. Hosa.
It's been a while but I know some hosas I had 15ish years ago had molded 1/4 in plugs, making them unrepairable unless you snipped them and added a new plug. This unfortunately messed up some.nestness since that connector'w wire was now half the length of the others.
 
jwin615 said:
Build them!
Check markertek and BTPA for cable.
SBP has a bunch for Neutrik XLR copies on sale for cheap right now too! Bet you can build a better cable for half the price or better vs. Hosa.
It's been a while but I know some hosas I had 15ish years ago had molded 1/4 in plugs, making them unrepairable unless you snipped them and added a new plug. This unfortunately messed up some.nestness since that connector'w wire was now half the length of the others.
Click to expand...
I have not found it cheaper to make cables vs buying them at all
 
I dreaded the call, but I got it yesterday. My sister is ready to have her house painted. Again. This will do thinned latex but will also do polyurethane without thinning. I am going to DIG finishing the Bassman 4x10 cab with this puppy!!! Just pulled the trigger on this and three additional paint containers for hot swap painting. What the hell, she has to pay for it and I get to keep it, lol....

1717986942999.png

IMG_1224.JPEG
 
Some rainy day fuzz. No regrets but a warning to y'all, the 3d printed brain knobs don't fit on my smooth pot shafts. They'll need to be glued to some knurled pots. Any suggestions on the best adhesive for that? CA? Epoxy? I would normally just avoid using them but look at these things... they're awesome. He threw in the aztek sunn as a freebie which is always appreciated. 20240610_125536.jpg
 
Mentaltossflycoon said:
Some rainy day fuzz. No regrets but a warning to y'all, the 3d printed brain knobs don't fit on my smooth pot shafts. They'll need to be glued to some knurled pots. Any suggestions on the best adhesive for that? CA? Epoxy? I would normally just avoid using them but look at these things... they're awesome. He threw in the aztek sunn as a freebie which is always appreciated. View attachment 76581
Click to expand...
E6000
 
Mentaltossflycoon said:
Some rainy day fuzz. No regrets but a warning to y'all, the 3d printed brain knobs don't fit on my smooth pot shafts. They'll need to be glued to some knurled pots. Any suggestions on the best adhesive for that? CA? Epoxy? I would normally just avoid using them but look at these things... they're awesome. He threw in the aztek sunn as a freebie which is always appreciated. View attachment 76581
Click to expand...
Those knobs are cool. I’m working on a 3D printed design for smooth shaft knobs with a locking screw but haven’t gotten to far on it yet. For glue probably CA but it depends on the 3d printed material. You might be able to heat the shafts and press fit them also, that’s what I did before I got them to fit with pressure only.
 
You must log in or register to reply here.

Similar threads

M
Diablo CB mod
Replies
0
Views
132
micmac
M
leadfoot
MattG's Egregiously Expensive Crunch
Replies
9
Views
787
MichaelW
MichaelW
VanWhy
DEMO Other* Pedals The Wonk Machine
Replies
3
Views
347
Synchrony Pedalworks
Synchrony Pedalworks
Fuzzonaut
Parasit Liberation Frequency Fuzz
Replies
4
Views
289
drgonzo1969
drgonzo1969
V
Kliche Buffer 1590a Builds
Replies
3
Views
263
OD is Glorious
OD is Glorious
Back
Top