Rat with a 3-band EQ?
- Thread starter Bio77
- Start date
t1redhands
Active member
If you're into stripboard at all I'd trust this one: ProCo / Fuzzdog 3-Band Rat
benny_profane
Well-known member
What’re you thinking? A Bax Rat? A pre-gain bass control, post-clipping mid-contour, and a low pass after the output buffer? Or something like a shredmaster with a pre-recovery FMV and a post-recovery mid-contour?
Cybercow
Well-known member
I've not seen any such specific Rat projects like that. But you can use one of the many Rat Analysis web pages (like Electro-Smash, ) to sort out where the tone stay is and replace it with something like the GuitarPCB "Tone TwEQ", the PedalPCB "Cold Turkey" or"Equilux Mini Equalizer" to get three active bands of EQ.
Bio77
Well-known member
Thanks guys, this is good information.
Hadn't given it a lot of in-depth thought, just had the general idea. I thought someone else must have had the same idea, I just haven't run across it. Is the shredmaster based at all on the Rat?
mdc
Well-known member
As far as PPCB options go, it'd be a cinch to take the normal muroidea/rat board and remove/jumper the filter; either delete the output or swap it for an internal trim; then run the output of that into the input of the tone job board. That'd give you a 3-band rat. You could probably play with the duncan TSC baxandall EQ values and make the treble control on the tone job behave the same as the filter control on a rat moving ccw from 12:00.
I built Blower Box clone with bass/treble and it's great. It can get very fuzzy and heavy.
dirtboxlayouts.blogspot.com
The Dunwich Volt Thrower adds clipping options (There's another version with a mid control, which I'd like to see):
dirtboxlayouts.blogspot.com
Here's a build report using the Effectslayouts PCB.
forum.pedalpcb.com
If you have a Rat already built, I'd look at those pedal schematics, including the Fuzzdog, and take Cybercow's and mdc's advice about splicing in an EQ. I used one of those Tone TwEQ boards on a DOD250
That Ratsaw is interesting. If HM-2 chainsaw isn't your thing, you can change the values of the three active controls to whatever frequencies you want.
Idiotbox Blower Box
dirtboxlayouts.blogspot.com
The Dunwich Volt Thrower adds clipping options (There's another version with a mid control, which I'd like to see):
Dunwich Amplification Volt Thrower - Big box version
A bit hesistant to upload this one since there is an unknown cap value and pot value. But a quite a few people have requested this one so I...
dirtboxlayouts.blogspot.com
Here's a build report using the Effectslayouts PCB.
Pepperbox (Volt Thrower)
Not just another rat ... it's what Dunwich did with the rat circuit --> Volt Thrower ! PCB is from Effects Layout. So, we have a biploar power supply, two band EQ, 6 clipping options and a gain recovery stage built around another LM308, although I subbed in an OP07 for that stage. But thanks to...
forum.pedalpcb.com
If you have a Rat already built, I'd look at those pedal schematics, including the Fuzzdog, and take Cybercow's and mdc's advice about splicing in an EQ. I used one of those Tone TwEQ boards on a DOD250
That Ratsaw is interesting. If HM-2 chainsaw isn't your thing, you can change the values of the three active controls to whatever frequencies you want.
JasonWickersham
Active member
BaxRAT , presence control , and clipping options such as this..
Id be on it like a fat kid on a box of HoHos
drgonzo1969
Well-known member
I hadn’t seen Inverted cross audio before. Just bought PCBs for that Thunderdome KT88 amp of theirs and their hyperfuzz pcb.
2 band rat
JasonWickersham
Active member
Thank you for the link, perusing the site, and REALLY like what I see. Bonus points for the Voodoo Lab trem clone.. had one sometime 2001-02 ish and quite enjoyed it.
