Missing Build Docs / Schematics

[temol]

Can we see the schematic for the Jump Drive?

 

[iamjackslackof]

Any chance of getting the Kliche Buffer BOM and schematic? Thank!

 

[Robert]

Kliche Buffer

https://www.pedalpcb.com/product/pcb156/ https://docs.pedalpcb.com/schematic/Schematic-KlicheBuffer.png

forum.pedalpcb.com

 

[Laundryroom David]

I think that must be it. Thanks for the feedback! (pun intended!!!) I had it chained after my Boss tuner pedal. A quick test putting it first resulted in some squeally "havoc". I'll give it a full go tonight but I think you are spot on. I'm relieved to know there is no issue in the build and I can stop troubleshooting. Thanks again!

Havoc is rad. But even in non-Havoc mode, this is quickly becoming one of my all time favourite pedals.

 

[Route14]

Havoc is rad. But even in non-Havoc mode, this is quickly becoming one of my all time favourite pedals.

Agreed. This is a great Rat variant and sounds awesome in either mode. I have the Cannon Fodder MKII queued up and can't wait.

 

[manfesto]

Could the BoM cheat sheet be put up for the Horsemeat? Thanks!

(Figure since I'm putting together a Mouser cart for the big film cap it'd be good to see if there are any other "gotcha" bits to add to the order)

 

[Locrian99]

Could the BoM cheat sheet be put up for the Horsemeat? Thanks!

(Figure since I'm putting together a Mouser cart for the big film cap it'd be good to see if there are any other "gotcha" bits to add to the order)

Seconded. Schematic would be cool as well.

 

[proozenburg]

Is there a BOM available for the Pro-10 dual ?

 

[harmaes]

Can we see the schematic for the Jump Drive?

And the BOM so I can order the parts before receiving the PCB.

 

[Dan0h]

Is there a BOM available for the Pro-10 dual ?

 

[proozenburg]

thanks!

 

[szukalski]

And the BOM so I can order the parts before receiving the PCB.

There’s nothing special if you already have an inventory of standard components. Pots can be seen in my build report.

If you don’t have such inventory.. can I recommend rounding resistors and capacitors up to ten for your next purchase

 

[jimilee]

There’s nothing special if you already have an inventory of standard components. Pots can be seen in my build report.

If you don’t have such inventory.. can I recommend rounding resistors and capacitors up to ten for your next purchase

At least 20. I buy them 100 at a time, sometimes 200 of the popular values.

 

[szukalski]

At least 20. I buy them 100 at a time, sometimes 200 of the popular values.

It really makes sense when you’ve got a backlog. At least for resistors, it’s not a big space issue.

 

[jimilee]

It really makes sense when you’ve got a backlog. At least for resistors, it’s not a big space issue.

Or if you’re planning a to have a back log of builds. I don’t know how many times I’ve just decided to build something and already had everything I needed. Pots are another story though. I’d love to be able to afford about 100 of each of the popular values.

 

[temol]

There’s nothing special if you already have an inventory of standard components. Pots can be seen in my build report.

If you don’t have such inventory.. can I recommend rounding resistors and capacitors up to ten for your next purchase

Oh Noooo.. we're trying to get a schematic here.... Stop it

 

[LukeFRC]

Low tide mini.... I'm sure it's workable out from the bigger low tide, but if you can stick something on it's page like "All caps need to be less than 5mm high and you need X connectors between the boards that would be super helpful!

 

[MattG]

How about the enclosure drilling template (pot and switch offsets) for the Jump Drive? I'm guessing it's the same as at least one other PedalPCB board...

Edit: also, what diodes? The PCB only says "GE". Which ones were found in the trace?

 

[Robusto]

Is there doc for the VIIB? (Boss VB-2)

 

[untamedfrontier]

Is there doc for the VIIB? (Boss VB-2)

+1, biasing instructions would be nice as well if possible.