Missing Build Docs / Schematics
- Thread starter Robert
- Start date
Phil hodson
Well-known member
Mr. Strypes
Active member
Hey, everybody! Are there build docs for the Salesman (Lerxt) Overdrive posted somewhere? Or a BOM perhaps?
Thanks in advance!
Thanks in advance!
Robert
Reverse Engineer
DeadAirMD
Well-known member
Definitely curious about the sizing for the standoffs. Already drilled the enclosure and the board is pretty snug, but would like to figure out what size screw/standoff/ mounting hardware fits those holes
@Phil hodson @DeadAirMD Here is the info for the standoff. They were spot on for me but I did my own drilling template.
Here was his answer to me.
Post in thread 'Is this the correct orientation ?' https://forum.pedalpcb.com/threads/is-this-the-correct-orientation.21161/post-268365
Here was his answer to me.
Post in thread 'Is this the correct orientation ?' https://forum.pedalpcb.com/threads/is-this-the-correct-orientation.21161/post-268365
Mr. Strypes
Active member
Thanks, Robert! You're awesome, bro!
Fama
Well-known member
A couple of Tayda drill template questions:
I assume the Antithesis is just the basic 4 knob layout, so pre-drilled boxes would work? Similarly Bellum Fuzz MK. II is a 3 knob.
But how about the Abyss? It doesn't seem to be the normal 5 knob layout, are there measurements somewhere or a Tayda drill template? I didn't find any. I can always measure the PCB but I don't trust myself to get it 100% right. Better than nothing else if it comes to that.
Similar question for the Fuzz Cadet, I do have a drill template for the Simulcast which I think is similar? I think I had some slight issues with the Simulcast when I built it, but nothing I can't fix afterwards, so if there's nothing better I can use that one (assuming the template is similar).
I assume the Antithesis is just the basic 4 knob layout, so pre-drilled boxes would work? Similarly Bellum Fuzz MK. II is a 3 knob.
But how about the Abyss? It doesn't seem to be the normal 5 knob layout, are there measurements somewhere or a Tayda drill template? I didn't find any. I can always measure the PCB but I don't trust myself to get it 100% right. Better than nothing else if it comes to that.
Similar question for the Fuzz Cadet, I do have a drill template for the Simulcast which I think is similar? I think I had some slight issues with the Simulcast when I built it, but nothing I can't fix afterwards, so if there's nothing better I can use that one (assuming the template is similar).
PapaBear
Well-known member
Abyss is 5 knob Type II
Fama
Well-known member
Thank you! Excellent!Abyss is 5 knob Type II
Edit: Anyone know about the Fuzz Cadet?
Edit2: Right, the Fuzz Cadet has the switch on the opposite side to Simulcast/Danube fuzz, so it definitely won't work with the same template. Anyone have the measurement for how far to the side it is on the Fuzz Cadet or should I measure it myself?
Edit3: For anyone else who's wondering who wants to use Tayda, looks like it's 4mm to the side from one of the side pots. So I got -20.5 for X and 12.7 for Y for the hole for the Voice switch.
Last edited:
kinkinaudio
New member
I'm hoping to get my hands on the build docs for the ADHD overdrive and Sproing Deluxe Reverb! 
chris.knudson
Well-known member
You don't need build docs for the ADHD. I've built two without them. Just follow the PCB, and you'll be fine. I do have the Sproing Deluxe in my build pile, but @Robert will probably post the build docs before I ever get around to building it -- in a few years.I'm hoping to get my hands on the build docs for the ADHD overdrive and Sproing Deluxe Reverb!
kinkinaudio
New member
Ooo! Great to know. You wouldn't happen to have a list of the components needed for the ADHD, would you? I know I'll need to order some components and I'm trying to get a Tayda order in this week!
chris.knudson
Well-known member
Resistors:
1X 1K
1X 2.2K
1X 4.7K
5X 10K
1X 18K
1X 22K
1X 33K
1X 39K
1X 150K
1X 220K
1X 470K
1X 1M
Caps:
2X 220p ceramic
1X 10n film
1X 22n film
1X 47n film
3X 100n film
3X 10u Electrolytic
Transistors:
2X 2N7000
ICs:
TL082
Diodes:
1X 5817
2X 1N34A (or equivalent)
Switches:
13PDT Footswitch
1PDT On/On
metanoisus
New member
I just built one. I correlated the screenshot on Pedalpcb.com using component numbers with the actual labels on the board, and cross referenced the single pendulum...here is a CSV. I am looking for a drill template, looks very tight.
Locrian99
Well-known member
You’ll be fine to
Build the version 1.1 which is a version 90% of us havent heard so id be cautious with that thought.