PedalPCB YATsa stato solida?

[fig]

Wow! I love it. Is that bus wire running from the jacks to the switch breakout board? Looks like you went a little light on the solder on the 3pdt switch.

Thank you! Yes, and also to the power jack. I usually fill one side of the switch pad, but yes sometimes it's a bit light. If it quits, I'll know where to look .

 

[fig]

That sir, is mighty fine!!

Thank you sir.

 

[Bricksnbeatles]

one step closer to the 1590A CS80 I've been hoping for

 

[BuddytheReow]

Sweet ride you got there @fig

 

[swelchy]

Whowza that's art

 

[Username123]

one step closer to the 1590A CS80 I've been hoping for.

I would say a moog system 55 is doable in a 125B right?

 

[Pauleo1214]

This is why I make weird stuff...I can't compete with that neatness!

 

[blackhatboojum]

Thanks Chris! It's roomy, like an old sedan but with that new car smell.

Like my dads ‘77 Ford LTD .

 

[andare]

As a trained architect I can tell the guts are structurally sound. Looks like a suspension bridge.

The red pot cozies are so cool. Do you happen to have a source, @fig ?

 

[Feral Feline]

Once again I post in the shadow of a beautiful build. This time it's @vigilante398 's Reactionary/Alarmist .

The official name is TBD, but I was given a special opportunity to build this and I had a blast with it! No other TS will do, no no no. Thanks Robert!

Since @Paradox916 nailed the TS logo, I've drawn a blank for a graphic...but I think the inside looks okay. It sounds like you know it should, but better somehow. You'll just have to build one.

I took a bit of liberty with the off-board wiring, kind of old meets new. A big thanks to @Mcknib for wire straightening tip. Forgive the flux at the power pads...I missed it.

SO ... BEAUTIFUL!

 

[music6000]

Once again I post in the shadow of a beautiful build. This time it's @vigilante398 's Reactionary/Alarmist .

The official name is TBD, but I was given a special opportunity to build this and I had a blast with it! No other TS will do, no no no. Thanks Robert!

Since @Paradox916 nailed the TS logo, I've drawn a blank for a graphic...but I think the inside looks okay. It sounds like you know it should, but better somehow. You'll just have to build one.

I took a bit of liberty with the off-board wiring, kind of old meets new. A big thanks to @Mcknib for wire straightening tip. Forgive the flux at the power pads...I missed it.

With a Black marker & a steady hand :

 

[fig]

As a trained architect I can tell the guts are structurally sound. Looks like a suspension bridge.

The red pot cozies are so cool. Do you happen to have a source, @fig ?

I do sir.

(Pot) Covers – The Best Anti-Static Protection – 12-Pack (Red or Violet) – GuitarPCB

guitarpcb.com

 

[Feral Feline]

"TBD", that stand for "Tube Bass Drive"?

 

[Coda]

I do sir.

(Pot) Covers – The Best Anti-Static Protection – 12-Pack (Red or Violet) – GuitarPCB

guitarpcb.com

And hear I was thinking you were a cheese smuggler this whole time…

 

[fig]

And hear I was thinking you were a cheese smuggler this whole time…

cheesy yes. smuggler not so much.

 

[jimilee]

Wow, I shall lay down my iron, for I am no longer worthy. That’s amazing sir.

 

[fig]

Wow, I shall lay down my iron, for I am no longer worthy. That’s amazing sir.

I've seen your work sir. Tis I who must gain game. Then, and only then, will I be gamey....er..

 

[music6000]

With a Black marker & a steady hand :

View attachment 24470

I was just thinking about TBD and with every tube screamer name already being milked & used, it must mean '' To Be Determined '' !!!

 

[Feral Feline]

And hear I was thinking you were a cheese smuggler this whole time…

AUDREY II meets PacMan...


"TBD" —
Two Bee Dissuaded
Trans-Bavarian Deutschlander
Tone Be Dimed
Trial By Damnation
Torts Before Denial
Tidily-winks Bidily-fiddy Didily-squat
Trussed Bondage & Discipline
Trespass Before Dishonour
Tim's Big ...


... DIY

 

[fig]

Tim's Big ...

...doodad