Sonomatic Delay

[jjjimi84]

Damn! I really thought I was done wanting more delays!

Me too mate, me too.

Board is on the way, any of you tayda geniuses wanna help an old fuddy duddy order a uv enclosure?

 

[Harry Klippton]

I wanna build one and I don't even like delay

 

[swyse]

I wanna build one and I don't even like delay

but what if this ones different, only one way to find out!

 

[Harry Klippton]

but what if this ones different, only one way to find out!

I like the way you think

 

[music6000]

The biggest challenge Members will have is cutting the piece of aluminium out of the 1590DD enclosure center post for the Output jack!
Look again at chongmagic 1st Pic on page 1.

 

[Feral Feline]

Dank u well, @Dutch66, het circuit is heel lekker.

Kunnen wij kijk naar het schematic, alstublieft?


Sorry voor mijn slechte Nederlands spraten.

Ik denkin dat mijn pedal's naam: Delay-Dropjes

Ik will hebben some dropjes, nu... double-zout.

 

[Guardians of the analog]

I wanna build one and I don't even like delay

 

[Bricksnbeatles]

The biggest challenge Members will have is cutting the piece of aluminium out of the 1590DD enclosure center post for the Output jack!
Look again at chongmagic 1st Pic on page 1.

Does Tayda’s DD have 6 screws? I know some DD enclosures are only 4-screw

 

[jimilee]

Does Tayda’s DD have 6 screws? I know some DD enclosures are only 4-screw

6

 

[Harry Klippton]

It has six

 

[Guardians of the analog]

6

It has six

It has a sextet of fasteners. Now we have a true echo

 

[ICTRock]

It has a sextet of fasteners. Now we have a true echo

 

[Dutch66]

Damn! I really thought I was done wanting more delays!

 

[Dutch66]

The biggest challenge Members will have is cutting the piece of aluminium out of the 1590DD enclosure center post for the Output jack!
Look again at chongmagic 1st Pic on page 1.

Dank u well, @Dutch66, het circuit is heel lekker.

Kunnen wij kijk naar het schematic, alstublieft?


Sorry voor mijn slechte Nederlands spraten.

Ik denkin dat mijn pedal's naam: Delay-Dropjes

Ik will hebben some dropjes, nu... double-zout.

Haha, 'dubbel zout' is quite a challenge! You can download the schematic from my FB group page, section/tab 'files' along with the UV printing file, Tayda drilling coordinates, modifications etc.. I just don't feel comfortable uploading it here, I don't wonna violate the pedalPCB forum rules.

 

[PedalPCB]

I just don't feel comfortable uploading it here, I don't wonna violate the pedalPCB forum rules.

You're more than welcome to post it here.

I do appreciate the consideration.

 

[Alan W]

The biggest challenge Members will have is cutting the piece of aluminium out of the 1590DD enclosure center post for the Output jack!
Look again at chongmagic 1st Pic on page 1.

1590DD Aluminum Die-Cast Enclosure

Unfinished die-cast aluminum 1590DD enclosure with lid. Includes four screws 1590DD enclosure size DIMENSIONS: 7.39 x 4.7 x 1.46" (188 x 120 x 37mm)

guitarpedalparts.com

4 holes available. ^^^

If you have a dremel like tool, or even a smaller hand drill, with a carbide end burr it’s very quick to grind away. I can send a picture of the type of burr, or a link to a set I got from AMZ that surprised me with its quality, especially since the set cost what I usually pay for a single burr.

 

[music6000]

The biggest challenge Members will have is cutting the piece of aluminium out of the 1590DD enclosure center post for the Output jack!
Look again at chongmagic 1st Pic on page 1.

This is how I would approach it.
I have a Dremel for this type of Work:

 

[Dutch66]

@Dutch66

I'm working up a UV Print design for @jjjimi84 and I was just curious if there are any scaling concerns with the graphic from the build doc. I want to make sure i don;t give him a bunk file, especially consdering the 1590DD plus UV is over $20.

I totally get you, but there's already a UV printing file (3 layers) available for the Sonomatic which has been used succesfully many times, as well as the drill coordinates. In all honesty, these are contributed over the years by members of my FB group, and are freely available for non-commercial use

 

[chongmagic]

I used a dremel to cut out the middle screw post, and I used the UV file from the @Dutch66 FB page as well as the drilling coordinates for Tayda.

 

[Dutch66]

@jjjimi84

View attachment 38298

I had to fix some things up and import the drill plan then scale it to size but I think this is it. I still need to put it into Tayda UV template form but when I'm done I'll forward it.

I used the back minus front command so that the enclosure color would come through the text and control rings but you could easily copy/paste the black outline and put it as RDG_White if you want the lettering, etc. to be white.

The (black only) design file for a water slide decal in the building documents has been used succesfully many times without any scaling issues ... It was made with Inkscape, but the exported .pdf seems to work fine. The file for UV printing has 3 layers (color, white & gloss) as per Tayda's requirements, and has also been used quite a few times without any hassle. Also, the drill coordinates available from the files section, line up perfectly with the UV.pdf I'm not sure what else I could say, but everything you need is already out there ... (thanks to our members)