Missing Build Docs / Schematics

[Locrian99]

I could’ve sworn I saw this somewhere before but now I can’t seem to find it. Seconded…

Found this should take care of it for me.

Cobbler preamp- component question

I got the new Cobbler board today and the build docs are pending. I wanted to double check a few components. There are several slots, like a diode, that read 3v3, 5V1 and 6V2. Are these components zener diodes at these voltages? Anything special with part selection for them?

forum.pedalpcb.com

 

[toto_]

Does anyone have the BOM of the Bobby Preamp please?

 

[Gt6371]

The diagram isn't drawn up yet but it's pretty straightforward.

+/- go to the corresponding lugs of the DC jack.

IN goes to Input Jack Tip
OUT goes to Output Jack Tip
Each jack grounds to their nearest GND pad

The two 3PDT breakout boards are direct pin-for-pin connections.

See this build report for an example:

Fordable Boost+Drive

Very straightforward build, @Robert said it’s a little tight, and it is, so you should definitely put the 3PDTs in first, solder only one leg of each pot, and then get everything test-fit first before tightening all the nuts and soldering all the pots (which I guess technically you should do for...

forum.pedalpcb.com

I'll get those schematics to you ASAP.

Cleric Fuzz

Cleric Fuzz

forum.pedalpcb.com

Decadence Preamp

Decadence Preamp

forum.pedalpcb.com

Are there any wiring or docs for the Byzantium? Thanks

 

[PangeaDestructor]

Is there a schematic for the Bobby available?

Edit - I see they are available for the Cetus and John, those are probably the same but with different component values or at least close enough to use so I'll go with that for the probe until the right one is available. In case anyone else is looking for the same thing.

 

[joaocosta88]

Could you please provide the documentation and drill templates for both synchrotrem and synchrowah?

 

[nate433]

Is there a drill template for the XS Drive (Xotic SL Drive)? I've been searching the forum and can't find anything. Can we just like use the hydra for the toggle locations, then use a 3knob template for the knobs?

 

[Darrencp]

Are the Mean Green Metal Machine build docs available yet ?
Cheers!

 

[manfesto]

Is there a BoM cheat sheet for the Bobby?

 

[Robert]

Is there a BoM cheat sheet for the Bobby?

Bobby Preamp

Bobby Preamp

forum.pedalpcb.com

 

[owlexifry]

Are the Mean Green Metal Machine build docs available yet ?
Cheers!

could just follow the little green scream machine docs and then use this schematic as your 'true' reference:

https://docs.pedalpcb.com/schematic/Schematic-MGMM.png

https://docs.pedalpcb.com/project/LGSM.pdf

 

[dcapo]

Is there a schematic for the protoboard? purchased one and having difficulty sourcing some of the componets, so I have them on back order but I want to use the board without the voltage regulators if possible while I wait for the parts. Wanted to see how the other components will be affected or what will or wont work without those components.

 

[Robert]

Is there a schematic for the protoboard?

https://docs.pedalpcb.com/project/Schematic-ProtoBoard.png

All of the power supplies are independent, omitting a regulator will only affect that particular voltage.

 

[dcapo]

Thanks Robert

 

[fontoponto]

Any info about the flock schematic and all the Victory style preamps?

Thanks for the Victory preamps. Is it planned to release the flock schematic?

 

[spaceboyaudiio]

Any build docs for Decadence Preamp? I was able to find a txt file with BOM, but not sure how to populate the board other than comparing to image of complete board found online

 

[Robert]

Thanks for the Victory preamps. Is it planned to release the flock schematic?

Yes of course, the schematic will be in the doc when it's posted.

Any build docs for Decadence Preamp? I was able to find a txt file with BOM, but not sure how to populate the board other than comparing to image of complete board found online

The component values are printed directly on the PCB.

I'm working through some build docs now but there are a few others ahead of this one.

 

[jimilee]

Yes of course, the schematic will be in the doc when it's posted.




The component values are printed directly on the PCB.

I'm working through some build docs now but there are a few others ahead of this one.

I’m coming to learn it’s so much easier with the values on the board.

 

[spaceboyaudiio]

Yes of course, the schematic will be in the doc when it's posted.




The component values are printed directly on the PCB.

I'm working through some build docs now but there are a few others ahead of this one.

I might be too new at this, but the board looks like the only values printed on it are for the pots. Seems like the markings are similar to what I got on the El Sol, where they related to a position and the build doc linked the position to the component. I guess the schematic would have both? Sorry for the confusion, I'm sure this is a me issue

 

[giovanni]

View attachment 41612

I might be too new at this, but the board looks like the only values printed on it are for the pots. Seems like the markings are similar to what I got on the El Sol, where they related to a position and the build doc linked the position to the component. I guess the schematic would have both? Sorry for the confusion, I'm sure this is a me issue

That is not a picture of the board you will get in the mail. The actual boards have values on the silkscreen.

 

[hybridpi]

Can I get equilux equalizer schematics?

Bumping this. I could use the bom/build docs and drill template too if it’s available.

Edit: found some info in another thread. Thanks! All I need now is that lnd150 mosfet!