Missing Build Docs / Schematics
- Thread starter Robert
- Start date
Looks like any 4-knob Type 1 drill template will work
crashguitar
Active member
I don't remember where it was posted but I have this:
(edit: also the above post lol)
I haven't seen a pdf version but this post has a link to the Tayda drill template for a 1590XX and I think I saw some other threads of how to translate the measurements of the Tayda drill template somewhere.
1590XX - PedalPCB Equilux
I just created this Tayda drill template based on the document that @Robert uploaded (see attached). It "should" work but it has not yet been verified. 1/13/23 Edit: @innerlight has confirmed the template with an adjustment to the drill sizes for the rotary switches. The linked template now...
forum.pedalpcb.com
Here are some other resources
Brett said you can message him for a template
Tayda drill template importing to scale in Adobe
I am preparing to make the Equilux. I have the drill template loaded in Tayda. If I use the image of the template from Tayda and paste it into Adobe Illustrator, will it keep the scale correctly? Thanks in advance.
forum.pedalpcb.com
Translating Tayda
Tayda drill template importing to scale in Adobe
I am preparing to make the Equilux. I have the drill template loaded in Tayda. If I use the image of the template from Tayda and paste it into Adobe Illustrator, will it keep the scale correctly? Thanks in advance.
forum.pedalpcb.com
@manfesto to clarify, with the Powder Blue drill template , pots and switch are at the same place? Because led is way lower in front of footswitch.
LED placement is the same as well (same place it is on the 6-knob layouts too, above the footswitch)
overdriver999
Member
no rush but the Cannon Fodder docs are still not available MKI & MKII
hendrix1201
New member
I want to know if the building docs for the XS Drive are going to be available soon 
Many thanks
Hi
Many thanksHi
t1redhands
Active member
Any chance of a schematic for the Hydra delay? Thanks!
Fama
Well-known member
Some drill template questions:
1.) Snozzberry Overdrive is just the standard 4 knob enclosure, right?
2.) Desolate fuzz would fit in a standard 5 knob enclosure? Or should I take the 5 knob template and change the hole sizes so they're a bit smaller for the switches? I think the switches should still work in pot sized holes though.
3.) Aberration fuzz looks like the standard 3 knob enclosure, I'm quite sure about this one.
4.) Viceroy overdrive is the standard 6 knob enclosure, but just with twice the footswitches and LEDs?
1.) Snozzberry Overdrive is just the standard 4 knob enclosure, right?
2.) Desolate fuzz would fit in a standard 5 knob enclosure? Or should I take the 5 knob template and change the hole sizes so they're a bit smaller for the switches? I think the switches should still work in pot sized holes though.
3.) Aberration fuzz looks like the standard 3 knob enclosure, I'm quite sure about this one.
4.) Viceroy overdrive is the standard 6 knob enclosure, but just with twice the footswitches and LEDs?
as a technology guy I refuse to read manuals, figure it out on my own, and then don’t write down anything so the next time I (or god forbid a coworker) need to do it I gotta do it all over again.
Two decades in IT and it hasn’t failed me yet.
1. Looks like, yep
2. Not quite, the holes are closer to a 4-knob layout (0.65” from center), but with a center hole in the bottom row
(Although in general you can put a switch in a pot sized hole with no issue)
3. Yep!
4. Basically.
If you take a look at the PedalPCB Drill template tool, it gives the spacings for most of the 125B layouts
benny_profane
Well-known member
Ah, the mortal enemy of the tech comms dept.
Laundryroom David
Keyboard Cowboy 🤠
Need a drill template? Looks from the tags on the pedalpcb website like you could pick a drill template from any of these to guide you: https://www.pedalpcb.com/product-tag/3-knob-type-1/
As a non tech guy, and non engineer, I usually hit search and dig around for a few minutes before I start a project. We are fortunate to have some actual engineers around here. Check out this thread for some excellent ideas: https://forum.pedalpcb.com/threads/crystal-drive.4242/
Last edited: